Resources

High-purity silver wire (d=0.500 mmd = 0.500\text{ mm}, L=1.00 mL = 1.00\text{ m}) is cooled from room temperature (293 K293\text{ K}) toward absolute zero (T→0 KT \to 0\text{ K}). At room temperature, the electrical resistivity is dominated by thermal lattice phonon scattering: ρphonon(293 K)=1.59×10−8 Ω⋅m\rho_{\text{phonon}}(293\text{ K}) = 1.59 \times 10^{-8}\ \Omega\cdot\text{m}. At cryogenic temperatures (T<10 KT < 10\text{ K}), phonon scattering vanishes as T5→0T^5 \to 0, leaving only residual impurity resistivity ρ0=1.25×10−11 Ω⋅m\rho_0 = 1.25 \times 10^{-11}\ \Omega\cdot\text{m}. (a) Calculate the Residual Resistivity Ratio (RRR=ρ(293 K)ρ0\text{RRR} = \frac{\rho(293\text{ K})}{\rho_0}). (b) Determine the asymptotic limit of the wire's electrical resistance RR as T→0 KT \to 0\text{ K}.

Answer and steps

Final answer

(a) RRR=1.27×103\text{RRR} = 1.27 \times 10^3; (b) RT→0 K=6.37×10−5 ΩR_{T \to 0\text{ K}} = 6.37 \times 10^{-5}\ \Omega

Steps

Part (a): Calculating the Residual Resistivity Ratio (RRR\text{RRR})

  1. Understand Matthiessen's Rule:
    According to Matthiessen's rule, the total electrical resistivity ρ(T)\rho(T) of a metal is the sum of temperature-dependent lattice phonon scattering and temperature-independent defect/impurity scattering: ρ(T)=ρphonon(T)+ρ0\rho(T) = \rho_{\text{phonon}}(T) + \rho_0 At room temperature (T=293 KT = 293\text{ K}), the phonon contribution dominates because ρphonon(293 K)=1.59×10−8 Ω⋅m≫ρ0=1.25×10−11 Ω⋅m\rho_{\text{phonon}}(293\text{ K}) = 1.59 \times 10^{-8}\ \Omega\cdot\text{m} \gg \rho_0 = 1.25 \times 10^{-11}\ \Omega\cdot\text{m}: ρ(293 K)≈ρphonon(293 K)=1.59×10−8 Ω⋅m\rho(293\text{ K}) \approx \rho_{\text{phonon}}(293\text{ K}) = 1.59 \times 10^{-8}\ \Omega\cdot\text{m}
  2. Calculate the Ratio:
    The Residual Resistivity Ratio (RRR\text{RRR}) quantifies the purity and crystalline perfection of the metal specimen: RRR=ρ(293 K)ρ0=1.59×10−8 Ω⋅m1.25×10−11 Ω⋅m=1.272×103≈1.27×103\text{RRR} = \frac{\rho(293\text{ K})}{\rho_0} = \frac{1.59 \times 10^{-8}\ \Omega\cdot\text{m}}{1.25 \times 10^{-11}\ \Omega\cdot\text{m}} = 1.272 \times 10^3 \approx 1.27 \times 10^3

Part (b): Determining the Limiting Resistance as T→0 KT \to 0\text{ K}

  1. Find the Cross-Sectional Area (AA) of the Wire:
    Given the diameter d=0.500 mm=5.00×10−4 md = 0.500\text{ mm} = 5.00 \times 10^{-4}\text{ m}: A=πd24=π(5.00×10−4 m)24≈1.9635×10−7 m2A = \frac{\pi d^2}{4} = \frac{\pi (5.00 \times 10^{-4}\text{ m})^2}{4} \approx 1.9635 \times 10^{-7}\text{ m}^2
  2. Calculate the Residual Resistance (RT→0 KR_{T \to 0\text{ K}}):
    As T→0 KT \to 0\text{ K}, thermal vibrations cease (ρphonon→0\rho_{\text{phonon}} \to 0), so the resistivity approaches its residual value ρ0\rho_0. Using the formula for electrical resistance: R=ρLAR = \rho \frac{L}{A} Substitute ρ0=1.25×10−11 Ω⋅m\rho_0 = 1.25 \times 10^{-11}\ \Omega\cdot\text{m} and L=1.00 mL = 1.00\text{ m}: RT→0 K=(1.25×10−11 Ω⋅m)(1.00 m)1.9635×10−7 m2≈6.366×10−5 Ω≈6.37×10−5 ΩR_{T \to 0\text{ K}} = \frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{1.9635 \times 10^{-7}\text{ m}^2} \approx 6.366 \times 10^{-5}\ \Omega \approx 6.37 \times 10^{-5}\ \Omega

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to divide the diameter by 2 when computing the cross-sectional area, using radius equal to diameter in πr² and obtaining a resistance that is four times too small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    RRR=(1.59×10−8 Ω⋅m)(1.25×10−11 Ω⋅m)=1272\text{RRR} = \frac{(1.59 \times 10^{-8}\ \Omega\cdot\text{m})}{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})} = 1272

  2. Step 2

    r = 0.500 ×\times 10^{-3} m\text{ m}   ⟹  \implies A = π\pi r^2 = π\pi (0.500 ×\times 10^{-3} m\text{ m})^2 = 7.854 ×\times 10^{-7} m\text{ m}^2

    Correct

    r = d2\frac{d}{2} = 0.250 ×\times 10^{-3} m\text{ m}   ⟹  \implies A = π\pi r^2 = πd24\frac{\pi d^2}{4} ≈\approx 1.9635 ×\times 10^{-7} m\text{ m}^2

    The problem states that the wire's diameter is d=0.500 mmd = 0.500\text{ mm}, not its radius. The radius is r=d2=0.250 mm=2.50×10−4 mr = \frac{d}{2} = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m}, so the true cross-sectional area is A=πd24≈1.964×10−7 m2A = \frac{\pi d^2}{4} \approx 1.964 \times 10^{-7}\text{ m}^2.

  3. Step 3

    R = ρ0LA\frac{\rho_0 L}{A} = (1.25×10−11 Ω⋅m)(1.00 m)(7.854×10−7 m2)\frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{(7.854 \times 10^{-7}\text{ m}^2)} = 1.59 ×\times 10^{-5}\ Ω\Omega

    Correct

    R = ρ0LA\frac{\rho_0 L}{A} = (1.25×10−11 Ω⋅m)(1.00 m)1.9635×10−7 m2\frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{1.9635 \times 10^{-7}\text{ m}^2} ≈\approx 6.37 ×\times 10^{-5}\ Ω\Omega

    Your resistance formula and arithmetic followed logically from your previous line, but substituting the oversized area produced a resistance value that is four times too small.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the residual resistivity ρ0\rho_0 governs the resistance as T→0 KT \to 0\text{ K}.

You accurately computed the ratio for RRR\text{RRR} in part (a).

You selected the correct cylindrical geometry formula R=ρLAR = \frac{\rho L}{A} for electrical resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Diameter-Radius Confusion

You assigned the given diameter d=0.500 mmd = 0.500\text{ mm} directly to the variable rr instead of dividing by 22.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating diameter dd with radius rr when calculating cross-sectional area A=πr2A = \pi r^2 leads to an area that is 22=42^2 = 4 times too large, propagating an inverse factor of 44 into the final resistance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Diameter vs. Radius Check
  • r=d2r = \frac{d}{2} or A=πd24A = \frac{\pi d^2}{4}

  • Whenever a circular dimension is given as diameter dd, immediately write r=d2r = \frac{d}{2} before substituting into A=πr2A = \pi r^2, or directly use A=πd24A = \frac{\pi d^2}{4}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the radius from the diameter: r=d2=0.500×10−3 m2=2.50×10−4 mr = \frac{d}{2} = \frac{0.500 \times 10^{-3}\text{ m}}{2} = 2.50 \times 10^{-4}\text{ m}.

  2. Calculate the true cross-sectional area: A=πr2=π(2.50×10−4 m)2≈1.9635×10−7 m2A = \pi r^2 = \pi (2.50 \times 10^{-4}\text{ m})^2 \approx 1.9635 \times 10^{-7}\text{ m}^2.

  3. Substitute AA, ρ0\rho_0, and LL into R=ρ0LAR = \frac{\rho_0 L}{A}: R=(1.25×10−11 Ω⋅m)(1.00 m)1.9635×10−7 m2≈6.37×10−5 ΩR = \frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{1.9635 \times 10^{-7}\text{ m}^2} \approx 6.37 \times 10^{-5}\ \Omega.

Final answer

(a) RRR≈1.27×103\text{RRR} \approx 1.27 \times 10^3; (b) RT→0 K≈6.37×10−5 ΩR_{T \to 0\text{ K}} \approx 6.37 \times 10^{-5}\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out r=d/2r = d / 2 as an explicit line before computing πr2\pi r^2.

  • Alternatively, memorize and use A=π4d2A = \frac{\pi}{4}d^2 directly whenever diameter is given.

  • Double-check dimensions against units to ensure you haven't swapped diameter and radius.

OverviewACEpath Teacher's Diagnosis

02 The student fails to convert the wire diameter from millimeters to meters, underestimating the cross-sectional area by a factor of 10⁶ and overestimating the resistance by 10⁶.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    RRR=(1.59×10−8)/(1.25×10−11)=1272\text{RRR} = (1.59 \times 10^{-8}) / (1.25 \times 10^{-11}) = 1272

  2. Step 2

    r=0.500 mm/2=0.250 mm  ⟹  A=π(0.250)2=0.1963 mm2r = 0.500\text{ mm} / 2 = 0.250\text{ mm} \implies A = \pi (0.250)^2 = 0.1963\text{ mm}^2

  3. Step 3

    R=(1.25×10−11 Ω⋅m)(1.00 m)0.1963=6.37×10−11 ΩR = \frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{0.1963} = 6.37 \times 10^{-11}\ \Omega

    Correct

    RT→0 K=ρ0LA=(1.25×10−11 Ω⋅m)(1.00 m)1.9635×10−7 m2≈6.37×10−5 ΩR_{T \to 0\text{ K}} = \frac{\rho_0 L}{A} = \frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{1.9635 \times 10^{-7}\text{ m}^2} \approx 6.37 \times 10^{-5}\ \Omega

    You substituted the area value 0.19630.1963 directly from mm2\text{mm}^2 without converting it to SI base units (m2\text{m}^2). Since 1 mm2=10−6 m21\text{ mm}^2 = 10^{-6}\text{ m}^2, the true area is 1.9635×10−7 m21.9635 \times 10^{-7}\text{ m}^2, yielding R=6.37×10−5 ΩR = 6.37 \times 10^{-5}\ \Omega.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the Residual Resistivity Ratio (RRR) as approximately 1.27×1031.27 \times 10^3.

You identified the correct relationship between diameter and cross-sectional area for a circular wire.

You selected the appropriate residual resistivity ρ0\rho_0 and formula R=ρL/AR = \rho L / A for the low-temperature limit.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You omitted the two-dimensional unit conversion factor when substituting an area expressed in square millimeters into a formula that requires square meters (1 mm2=10−6 m21\text{ mm}^2 = 10^{-6}\text{ m}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI unit consistency before substitution
  • Every parameter in R=ρLAR = \rho \frac{L}{A} must match the base units of resistivity (Ω⋅m\Omega\cdot\text{m}), meaning length must be in m\text{m} and cross-sectional area in m2\text{m}^2.

  • Always convert lengths to meters before squaring to compute area: r=0.250 mm=2.50×10−4 m  ⟹  A=πr2=1.963×10−7 m2r = 0.250\text{ mm} = 2.50 \times 10^{-4}\text{ m} \implies A = \pi r^2 = 1.963 \times 10^{-7}\text{ m}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the cross-sectional area to square meters: A=0.19635 mm2×(10−3 m/1 mm)2=1.9635×10−7 m2A = 0.19635\text{ mm}^2 \times \left(10^{-3}\text{ m} / 1\text{ mm}\right)^2 = 1.9635 \times 10^{-7}\text{ m}^2.

  2. Substitute ρ0=1.25×10−11 Ω⋅m\rho_0 = 1.25 \times 10^{-11}\ \Omega\cdot\text{m}, L=1.00 mL = 1.00\text{ m}, and A=1.9635×10−7 m2A = 1.9635 \times 10^{-7}\text{ m}^2 into R=ρLAR = \frac{\rho L}{A}.

Final answer

RT→0 K=6.37×10−5 ΩR_{T \to 0\text{ K}} = 6.37 \times 10^{-5}\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Convert wire diameters directly to meters (d=5.00×10−4 md = 5.00 \times 10^{-4}\text{ m}) at the very start of your scratch work before computing area.

  • Practice converting derived units involving powers, keeping in mind that (10−3 m)2=10−6 m2(10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the ratio definition for RRR, dividing residual resistivity by room temperature resistivity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    RRR=ρ0ρ(293 K)=1.25×10−11 Ω⋅m1.59×10−8 Ω⋅m=7.86×10−4\text{RRR} = \frac{\rho_0}{\rho(293\text{ K})} = \frac{1.25 \times 10^{-11}\ \Omega\cdot\text{m}}{1.59 \times 10^{-8}\ \Omega\cdot\text{m}} = 7.86 \times 10^{-4}

    Correct

    RRR=ρ(293 K)ρ0=1.59×10−8 Ω⋅m1.25×10−11 Ω⋅m≈1.27×103\text{RRR} = \frac{\rho(293\text{ K})}{\rho_0} = \frac{1.59 \times 10^{-8}\ \Omega\cdot\text{m}}{1.25 \times 10^{-11}\ \Omega\cdot\text{m}} \approx 1.27 \times 10^3

    You inverted the quotient for the Residual Resistivity Ratio. RRR is defined as room-temperature resistivity divided by residual resistivity, ρ(293 K)ρ0\frac{\rho(293\text{ K})}{\rho_0}, reflecting how many times higher room-temperature resistance is compared to the impurity limit.

  2. Step 2

    A=π(0.250×10−3 m)2=1.9635×10−7 m2A = \pi (0.250 \times 10^{-3}\text{ m})^2 = 1.9635 \times 10^{-7}\text{ m}^2

  3. Step 3

    R=(1.25×10−11 Ω⋅m)(1.00 m)(1.9635×10−7 m2)=6.37×10−5 ΩR = \frac{(1.25 \times 10^{-11}\ \Omega\cdot\text{m})(1.00\text{ m})}{(1.9635 \times 10^{-7}\text{ m}^2)} = 6.37 \times 10^{-5}\ \Omega

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the cross-sectional area from the given diameter using consistent SI units.

You correctly identified that the electrical resistivity as T→0 KT \to 0\text{ K} approaches the residual resistivity ρ0\rho_0.

You applied the geometry-resistance formula R=ρLAR = \frac{\rho L}{A} accurately to obtain the limiting resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Ratio Definition

You set up RRR as ρ0ρ(293 K)\frac{\rho_0}{\rho(293\text{ K})} rather than ρ(293 K)ρ0\frac{\rho(293\text{ K})}{\rho_0}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the phrase 'Residual Resistivity Ratio' with having residual resistivity ρ0\rho_0 in the numerator, overlooking that RRR is conventionally defined as the high-temperature (room temperature) resistivity normalized by the residual impurity floor.

REASONING PATH
Your ACEpath teacher’s suggested approach
Physical Magnitude of RRR
  • High-purity metals have fewer defects, so residual resistivity ρ0\rho_0 is very small compared to room-temperature resistivity ρ(293 K)\rho(293\text{ K}), making RRR≫1\text{RRR} \gg 1.

  • Whenever you compute an RRR for a pure metal, check that your result is a large dimensionless number (typically 10210^2 to 10410^4), never a decimal less than 11.

Ratio Definition Check
  • RRR=ρ(293 K)ρ0=ρroomρresidual\text{RRR} = \frac{\rho(293\text{ K})}{\rho_0} = \frac{\rho_{\text{room}}}{\rho_{\text{residual}}}.

  • Write out the variable names with explicit temperature tags before substituting numerical values into the fraction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall the standard definition of the Residual Resistivity Ratio: RRR=ρ(293 K)ρ0\text{RRR} = \frac{\rho(293\text{ K})}{\rho_0}.

  2. Substitute the room temperature resistivity in the numerator and residual resistivity in the denominator: RRR=1.59×10−8 Ω⋅m1.25×10−11 Ω⋅m\text{RRR} = \frac{1.59 \times 10^{-8}\ \Omega\cdot\text{m}}{1.25 \times 10^{-11}\ \Omega\cdot\text{m}}.

  3. Evaluate the quotient: RRR=1.272×103≈1.27×103\text{RRR} = 1.272 \times 10^3 \approx 1.27 \times 10^3.

Final answer

(a) RRR=1.27×103\text{RRR} = 1.27 \times 10^3; (b) RT→0 K=6.37×10−5 ΩR_{T \to 0\text{ K}} = 6.37 \times 10^{-5}\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Matthiessen's rule separates temperature-dependent phonon scattering from static defect scattering.

  • Practice checking whether purity metrics like RRR should yield values greater than 1 or less than 1 based on their physical interpretation.

  • Try the follow-up practice problems to reinforce cryogenic resistivity and wire resistance calculations.

Lock it in

Similar question

01

A copper wire has a diameter of d=1.00 mmd = 1.00\text{ mm} and a length of L=2.00 mL = 2.00\text{ m}. At cryogenic temperatures, its residual resistivity is ρ0=2.00×10−11 Ω⋅m\rho_0 = 2.00 \times 10^{-11}\ \Omega\cdot\text{m}. Calculate the wire's residual resistance R0R_0.

Answer

R0≈5.09×10−5 ΩR_0 \approx 5.09 \times 10^{-5}\ \Omega. First, r=d2=0.500 mm=5.00×10−4 mr = \frac{d}{2} = 0.500\text{ mm} = 5.00 \times 10^{-4}\text{ m}. Then A=πr2=π(5.00×10−4 m)2≈7.854×10−7 m2A = \pi r^2 = \pi (5.00 \times 10^{-4}\text{ m})^2 \approx 7.854 \times 10^{-7}\text{ m}^2. Finally, R0=ρ0LA=(2.00×10−11 Ω⋅m)(2.00 m)7.854×10−7 m2≈5.09×10−5 ΩR_0 = \frac{\rho_0 L}{A} = \frac{(2.00 \times 10^{-11}\ \Omega\cdot\text{m})(2.00\text{ m})}{7.854 \times 10^{-7}\text{ m}^2} \approx 5.09 \times 10^{-5}\ \Omega.

02

An aluminum sample with residual resistivity ratio RRR=800\text{RRR} = 800 has a room-temperature resistivity of ρ(293 K)=2.65×10−8 Ω⋅m\rho(293\text{ K}) = 2.65 \times 10^{-8}\ \Omega\cdot\text{m}. (a) Find its residual resistivity ρ0\rho_0. (b) A circular aluminum wire drawn from this batch has diameter d=0.400 mmd = 0.400\text{ mm} and length L=0.500 mL = 0.500\text{ m}. Find its resistance at T→0 KT \to 0\text{ K}.

Answer

(a) ρ0=ρ(293 K)RRR=2.65×10−8 Ω⋅m800≈3.31×10−11 Ω⋅m\rho_0 = \frac{\rho(293\text{ K})}{\text{RRR}} = \frac{2.65 \times 10^{-8}\ \Omega\cdot\text{m}}{800} \approx 3.31 \times 10^{-11}\ \Omega\cdot\text{m}. (b) Wire radius is r=0.200 mm=2.00×10−4 mr = 0.200\text{ mm} = 2.00 \times 10^{-4}\text{ m}, giving A=πr2≈1.257×10−7 m2A = \pi r^2 \approx 1.257 \times 10^{-7}\text{ m}^2. Then R0=ρ0LA=(3.3125×10−11 Ω⋅m)(0.500 m)1.257×10−7 m2≈1.32×10−4 ΩR_0 = \frac{\rho_0 L}{A} = \frac{(3.3125 \times 10^{-11}\ \Omega\cdot\text{m})(0.500\text{ m})}{1.257 \times 10^{-7}\text{ m}^2} \approx 1.32 \times 10^{-4}\ \Omega.

03

Two cylindrical wires XX and YY are made of the same high-purity metal at T→0 KT \to 0\text{ K}. Wire XX has diameter dd and length LL. Wire YY has diameter 2d2d and length 4L4L. If wire XX has a residual resistance of RX=8.0×10−5 ΩR_X = 8.0 \times 10^{-5}\ \Omega, find the residual resistance RYR_Y of wire YY.

Answer

RY=8.0×10−5 ΩR_Y = 8.0 \times 10^{-5}\ \Omega. Resistance is given by R=ρLA=ρLπ(d/2)2=4ρLπd2R = \frac{\rho L}{A} = \frac{\rho L}{\pi (d/2)^2} = \frac{4\rho L}{\pi d^2}. For wire YY, length increases by a factor of 4, while the area increases by a factor of 22=42^2 = 4. Therefore, RY=4ρ(4L)π(2d)2=4ρ(4L)π(4d2)=RX=8.0×10−5 ΩR_Y = \frac{4\rho (4L)}{\pi (2d)^2} = \frac{4\rho (4L)}{\pi (4d^2)} = R_X = 8.0 \times 10^{-5}\ \Omega.

Loading workspace…