Resources
A sample of an aqueous solution contains ions at a concentration of . Solid sodium chloride, , is slowly added with stirring (assume negligible volume change). For lead(II) chloride, , at . Calculate the minimum concentration of chloride ions, , required to initiate precipitation of , and determine the minimum mass in grams of solid () that must be added to the sample.
Answer and steps
Final answer
Minimum ; minimum mass of .
Steps
Write the Dissolution Equilibrium and the Solubility Product Expression
Lead(II) chloride dissolves in water according to the equilibrium equation:
The solubility product expression is:
Precipitation begins at the threshold where the ion product quotient equals :
Calculate the Minimum Required for Precipitation
Rearrange the expression to solve for the concentration of chloride ions:
Substitute the given values:
Rounding to two significant figures gives:
Common Pitfall: Do not forget to square the term in the equilibrium expression. The stoichiometric coefficient of for appears as an exponent in . However, do not substitute for here, because chloride ions are introduced independently from an external source (), rather than by dissolving pure in water.
Calculate the Minimum Mass of Solid Needed
Since sodium chloride dissociates completely according to , each mole of supplies one mole of .
Convert the solution volume to liters:
Determine the moles of (and thus ) required:
Convert moles to mass using the molar mass of ():
Rounding to two significant figures:
Typical errors
01 The student forgets to square the chloride ion concentration in the Ksp expression, writing Ksp = [Pb²⁺][Cl⁻].
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Lead(II) chloride dissociates as , so the stoichiometric coefficient of for requires squaring in the solubility product expression.
- Step 2Correct
Your dimensional analysis and stoichiometric calculations from to grams of were executed correctly, but the resulting value was affected by the incorrect from Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related the amount of chloride ions to the mass of solid using molar volume and molar mass.
You correctly identified that precipitation initiates when the reaction quotient equals .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou omitted the exponent corresponding to the stoichiometric coefficient when writing the expression for a salt with a cation-to-anion ratio.
REASONING PATH
Your ACEpath teacher’s suggested approach- Write the balanced dissolution equilibrium first
For any slightly soluble salt , the solubility product expression is .
Always balance the dissociation reaction before writing , and check that every stoichiometric coefficient appears as an exponent on its ion's concentration.
- Distinguish pure salt dissolution from independent ion addition
When an ion is added from an external source such as , its concentration is represented directly as rather than , but the exponent on in the law of mass action remains mandatory.
Keep the exponent intact from the balanced equation, substitute the known ion concentration, and solve for the unknown ion concentration by taking the appropriate root.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete solubility product expression: .
Substitute the known values: .
Solve for : .
Calculate moles of needed: .
Convert moles to mass: .
Minimum ; minimum mass of
02 The student mistakenly squares the stoichiometric coefficient inside the bracket, setting [Cl⁻] = 2x and calculating Ksp = [Pb²⁺](2[Cl⁻])² or 4[Pb²⁺][Cl⁻]².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You defined the solubility product as . The equilibrium expression is strictly . The stoichiometric coefficient appears only as an exponent, not as a multiplier on .
- Step 2Correct
You carried out the concentration-to-mole calculation correctly, but the result was affected by the incorrect value of from Step 1.
- Step 3Correct
You correctly multiplied by the molar mass of and rounded to two significant figures, but the starting mole value was lower due to the error in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the onset of precipitation occurs when the ion product quotient reaches .
You correctly calculated the moles of solute by multiplying molarity by volume in liters.
You used the correct molar mass to convert moles of into grams.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted instead of into the equilibrium expression.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the molar solubility formula for dissolving a pure solid in water (where , giving ) with the fundamental law. When expressing equilibrium conditions directly in terms of ion concentrations, the stoichiometric coefficient is only an exponent: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometry in Ksp
For a salt , the equilibrium expression is always .
Never insert stoichiometric multipliers inside the brackets when the variable represents the actual ion concentration.
- Pure Water vs. External Ion Sources
Use multipliers like only when defining ion concentrations in terms of a single molar solubility variable during dissolution of a pure salt.
When adding an external reagent such as solid , treat as its own independent concentration variable.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the solubility product expression for : .
Solve for the required chloride concentration: .
Calculate the moles of needed in : .
Convert moles to mass: .
Minimum ; minimum mass of
03 The student omits multiplying by the solution volume (200.0 mL), treating the molar concentration directly as the moles of NaCl needed.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Molarity is moles per liter of solution. To find the actual moles of needed in a () sample, you must multiply the concentration by the volume (). Setting directly equal to molarity assumes a volume of .
- Step 3Correct
Your conversion from moles to mass using the molar mass was algebraically carried out correctly, but the resulting value is too large because it inherited the unscaled mole quantity from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly wrote the solubility product expression .
You correctly solved the quadratic relationship to find the threshold concentration .
You correctly applied the molar mass factor () to convert moles of into mass.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou equated molar concentration (mol/L) directly with total moles (mol), neglecting to scale by the specific solution volume ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Connecting Molarity and Amount of Substance
, where is in liters.
Always verify the solution volume given in the problem prompt before converting between concentration and grams.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the solution volume to liters: .
Calculate moles of : .
Convert moles of to grams: .
Minimum ; minimum mass of
Lock it in
How is the expression formulated for the generic salt ?
. Each stoichiometric coefficient becomes the power (exponent) of that ion's concentration.
Similar question
A solution has . Solid is added slowly. If , what is the minimum needed to initiate precipitation of ?
Answer
. Key steps: Dissolution is , so . Rearranging gives .
A sample contains of . Solid () is added without changing the volume. Given , calculate the minimum mass of required to start precipitation.
Answer
. Key steps: . Moles of . Mass of .
A solution contains and . Solid is added gradually. Given and , which cation precipitates first, and what is the concentration of that cation remaining in solution when the second cation just begins to precipitate?
Answer
precipitates first; remaining . Key steps: precipitates when ; precipitates when . Since , precipitates first. When starts precipitating, . At that point, .