Resources

In an analytical chemistry laboratory, a student standardizes a concentrated sulfuric acid (H2SO4\text{H}_2\text{SO}_4) stock solution. The student carefully pipettes a 5.00 mL5.00\text{ mL} aliquot of the stock H2SO4\text{H}_2\text{SO}_4 into a 250.0 mL250.0\text{ mL} volumetric flask, dilutes to the calibration mark with deionized water, and inverts the flask to mix thoroughly. A 25.00 mL25.00\text{ mL} aliquot of this diluted solution is then titrated with a standardized 0.1040 M NaOH0.1040\text{ M }\text{NaOH} solution using a calibrated buret. The titration requires 28.85 mL28.85\text{ mL} of NaOH\text{NaOH} to reach the phenolphthalein endpoint according to the reaction H2SO4(aq)+2NaOH(aq)→Na2SO4(aq)+2H2O(l)\text{H}_2\text{SO}_4\text{(aq)} + 2\text{NaOH(aq)} \rightarrow \text{Na}_2\text{SO}_4\text{(aq)} + 2\text{H}_2\text{O(l)}. Calculate the molarity of the original concentrated stock sulfuric acid solution.

Answer and steps

Final answer

3.00 M3.00\text{ M}

Steps

01

Calculate the moles of NaOH\ce{NaOH} used in the titration

To find the molarity of the stock sulfuric acid solution, we work backward from the titration data to the diluted solution, and then apply the dilution relationship.

The volume of NaOH\ce{NaOH} used is 28.85 mL=0.02885 L28.85\text{ mL} = 0.02885\text{ L}. Using the molarity formula, n=M⋅Vn = M \cdot V: n(NaOH)=0.1040 mol/L⋅0.02885 L=3.0004×10−3 moln(\ce{NaOH}) = 0.1040\text{ mol/L} \cdot 0.02885\text{ L} = 3.0004 \times 10^{-3}\text{ mol}

02

Determine the moles of HX2SOX4\ce{H2SO4} in the 25.00 mL25.00\text{ mL} aliquot

From the balanced chemical equation: HX2SOX4(aq)+2 NaOH(aq)→NaX2SOX4(aq)+2 HX2O(l)\ce{H2SO4(aq) + 2NaOH(aq) -> Na2SO4(aq) + 2H2O(l)}

The stoichiometric ratio between HX2SOX4\ce{H2SO4} and NaOH\ce{NaOH} is 1:21:2.

Pitfall: Do not assume a 1:11:1 ratio. Because sulfuric acid is diprotic, each mole of HX2SOX4\ce{H2SO4} requires two moles of OHX−\ce{OH-} to neutralize completely.

n(HX2SOX4)aliquot=12⋅n(NaOH)=3.0004×10−3 mol2=1.5002×10−3 moln(\ce{H2SO4})_{\text{aliquot}} = \frac{1}{2} \cdot n(\ce{NaOH}) = \frac{3.0004 \times 10^{-3}\text{ mol}}{2} = 1.5002 \times 10^{-3}\text{ mol}

03

Find the molarity of the diluted HX2SOX4\ce{H2SO4} solution

The 1.5002×10−3 mol1.5002 \times 10^{-3}\text{ mol} of HX2SOX4\ce{H2SO4} was contained in an aliquot volume of 25.00 mL=0.02500 L25.00\text{ mL} = 0.02500\text{ L}: Mdilute=n(HX2SOX4)aliquotValiquot=1.5002×10−3 mol0.02500 L=0.060008 MM_{\text{dilute}} = \frac{n(\ce{H2SO4})_{\text{aliquot}}}{V_{\text{aliquot}}} = \frac{1.5002 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.060008\text{ M}

04

Calculate the molarity of the original stock solution

The diluted solution was prepared by diluting Vstock=5.00 mLV_{\text{stock}} = 5.00\text{ mL} of the stock acid to a total volume of Vdilute=250.0 mLV_{\text{dilute}} = 250.0\text{ mL}.

Using the dilution equation Mstock⋅Vstock=Mdilute⋅VdiluteM_{\text{stock}} \cdot V_{\text{stock}} = M_{\text{dilute}} \cdot V_{\text{dilute}}: Mstock=Mdilute⋅VdiluteVstockM_{\text{stock}} = M_{\text{dilute}} \cdot \frac{V_{\text{dilute}}}{V_{\text{stock}}} Mstock=0.060008 M⋅250.0 mL5.00 mL=0.060008 M⋅50.0=3.0004 MM_{\text{stock}} = 0.060008\text{ M} \cdot \frac{250.0\text{ mL}}{5.00\text{ mL}} = 0.060008\text{ M} \cdot 50.0 = 3.0004\text{ M}

Rounding to three significant figures (limited by the 5.00 mL5.00\text{ mL} pipetted volume) gives: Mstock=3.00 MM_{\text{stock}} = 3.00\text{ M}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes a 1:1 stoichiometric ratio between H2SO4 and NaOH, failing to divide the moles of NaOH by 2 and doubling the calculated stock molarity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(NaOH)=0.1040 M×0.02885 L=0.0030004 moln(\ce{NaOH}) = 0.1040\text{ M} \times 0.02885\text{ L} = 0.0030004\text{ mol}

  2. Step 2

    n(HX2SOX4 in 25.00 mL)=n(NaOH)=0.0030004 moln(\ce{H2SO4}\text{ in } 25.00\text{ mL}) = n(\ce{NaOH}) = 0.0030004\text{ mol}

    Correct

    n(HX2SOX4 in 25.00 mL)=12n(NaOH)=1.5002×10−3 moln(\ce{H2SO4}\text{ in } 25.00\text{ mL}) = \frac{1}{2} n(\ce{NaOH}) = 1.5002 \times 10^{-3}\text{ mol}

    Sulfuric acid is a diprotic acid that reacts with sodium hydroxide in a 1:21:2 molar ratio (HX2SOX4+2 NaOH→NaX2SOX4+2 HX2O\ce{H2SO4 + 2NaOH -> Na2SO4 + 2H2O}). You need to divide the moles of NaOH\ce{NaOH} by 22 to find the moles of HX2SOX4\ce{H2SO4}.

  3. Step 3

    M(diluted HX2SOX4)=0.0030004 mol/0.02500 L=0.1200 MM(\text{diluted } \ce{H2SO4}) = 0.0030004\text{ mol} / 0.02500\text{ L} = 0.1200\text{ M}

    Correct

    M(diluted HX2SOX4)=1.5002×10−3 mol0.02500 L=0.06001 MM(\text{diluted } \ce{H2SO4}) = \frac{1.5002 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.06001\text{ M}

    Your division by the aliquot volume was executed correctly, but the value is twice what it should be due to the mole ratio error in Step 2.

  4. Step 4

    M(stock)=0.1200 M×(250.0 mL5.00 mL)=6.00 MM(\text{stock}) = 0.1200\text{ M} \times \left(\frac{250.0\text{ mL}}{5.00\text{ mL}}\right) = 6.00\text{ M}

    Correct

    M(stock)=0.06001 M×(250.0 mL5.00 mL)=3.00 MM(\text{stock}) = 0.06001\text{ M} \times \left(\frac{250.0\text{ mL}}{5.00\text{ mL}}\right) = 3.00\text{ M}

    Your dilution factor formulation was set up properly, but the propagated error from Step 2 led to an inflated stock concentration of 6.00 M6.00\text{ M} instead of 3.00 M3.00\text{ M}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the moles of titrant NaOH\ce{NaOH} from its concentration and volume.

You correctly identified and applied the volume of the titrated aliquot to compute molarity.

You applied the dilution factor VdiluteVstock=250.0 mL5.00 mL=50.0\frac{V_{\text{dilute}}}{V_{\text{stock}}} = \frac{250.0\text{ mL}}{5.00\text{ mL}} = 50.0 accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Stoichiometric Ratio Omission in Polyprotic Acid Titration

You treated the reaction as equimolar (1:11:1) between acid and base, forgetting that sulfuric acid neutralizes two hydroxide ions per formula unit.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating equivalence of reacting species with a 1:11:1 molar ratio rather than balancing equivalents (nHX+=nOHX−n_{\ce{H+}} = n_{\ce{OH-}}) or using coefficients from the balanced equation (nHX2SOX4=12nNaOHn_{\ce{H2SO4}} = \frac{1}{2} n_{\ce{NaOH}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Verify Acid-Base Stoichiometric Coefficients
  • In titration stoichiometry, n(acid)a=n(base)b\frac{n(\text{acid})}{a} = \frac{n(\text{base})}{b}, where aa and bb are the coefficients from the balanced equation.

  • Before equating moles, write the balanced neutralization equation and convert moles of titrant to moles of analyte using the stoichiometric ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Account for the diprotic nature of HX2SOX4\ce{H2SO4}: n(HX2SOX4)=12n(NaOH)=0.0030004 mol2=0.0015002 moln(\ce{H2SO4}) = \frac{1}{2} n(\ce{NaOH}) = \frac{0.0030004\text{ mol}}{2} = 0.0015002\text{ mol}.

  2. Find the molarity of the diluted solution: Mdilute=0.0015002 mol0.02500 L=0.060008 MM_{\text{dilute}} = \frac{0.0015002\text{ mol}}{0.02500\text{ L}} = 0.060008\text{ M}.

  3. Multiply by the dilution factor to determine the stock concentration: Mstock=0.060008 M×250.0 mL5.00 mL=3.0004 MM_{\text{stock}} = 0.060008\text{ M} \times \frac{250.0\text{ mL}}{5.00\text{ mL}} = 3.0004\text{ M}.

Final answer

3.00 M3.00\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the balanced reaction equation explicitly before starting titration math.

  • Flag polyprotic acids (like HX2SOX4\ce{H2SO4} or HX3POX4\ce{H3PO4}) or polyhydroxy bases (like Ca(OH)X2\ce{Ca(OH)2}) immediately to ensure stoichiometric factors are not missed.

  • Practice two-stage analytical problems combining dilution and titration to reinforce tracking concentrations through each aliquot.

OverviewACEpath Teacher's Diagnosis

02 The student forgets that only a 25.00 mL aliquot was titrated from the 250.0 mL flask, assuming the titrated moles represent the entire 5.00 mL stock sample.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    n(NaOH)=0.1040 M×0.02885 L=0.0030004 moln(\text{NaOH}) = 0.1040\text{ M} \times 0.02885\text{ L} = 0.0030004\text{ mol}

  2. Step 2

    n(H2SO4)=0.0030004 mol2=0.0015002 moln(\text{H}_2\text{SO}_4) = \frac{0.0030004\text{ mol}}{2} = 0.0015002\text{ mol}

  3. Step 3

    M(stock)=0.0015002 mol0.00500 L=0.300 MM(\text{stock}) = \frac{0.0015002\text{ mol}}{0.00500\text{ L}} = 0.300\text{ M}

    Correct

    Mstock=0.0015002 mol×(250.0 mL25.00 mL)0.00500 L=3.00 MM_{\text{stock}} = \frac{0.0015002\text{ mol} \times \left(\frac{250.0\text{ mL}}{25.00\text{ mL}}\right)}{0.00500\text{ L}} = 3.00\text{ M}

    You treated the 0.0015002 mol0.0015002\text{ mol} of H2SO4\text{H}_2\text{SO}_4 as if it were the total amount from the 5.00 mL5.00\text{ mL} stock. That quantity was only contained in the 25.00 mL25.00\text{ mL} titration aliquot, which represents one-tenth of the total 250.0 mL250.0\text{ mL} diluted solution.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the moles of titrant accurately from its concentration and volume.

You correctly accounted for the diprotic nature of sulfuric acid using the 1:21:2 mole ratio.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted aliquot scaling factor

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the moles of solute titrated in a small aliquot with the total moles of solute present in the entire diluted volumetric flask.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for Aliquot Fraction
  • An aliquot taken from a thoroughly mixed volumetric flask contains only a fraction of the total moles: ntotal=naliquot×VtotalValiquotn_{\text{total}} = n_{\text{aliquot}} \times \frac{V_{\text{total}}}{V_{\text{aliquot}}}.

  • Always multiply the titrated moles by the ratio VflaskValiquot\frac{V_{\text{flask}}}{V_{\text{aliquot}}} before calculating the original stock amount, or find MdiluteM_{\text{dilute}} first and then use M1V1=M2V2M_1V_1 = M_2V_2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the total moles in the 250.0 mL250.0\text{ mL} flask: ntotal=0.0015002 mol×250.0 mL25.00 mL=0.015002 moln_{\text{total}} = 0.0015002\text{ mol} \times \frac{250.0\text{ mL}}{25.00\text{ mL}} = 0.015002\text{ mol}.

  2. Calculate the stock molarity using the initial 5.00 mL5.00\text{ mL} volume: Mstock=0.015002 mol0.00500 L=3.0004 MM_{\text{stock}} = \frac{0.015002\text{ mol}}{0.00500\text{ L}} = 3.0004\text{ M}.

  3. Round to three significant figures: 3.00 M3.00\text{ M}.

Final answer

3.00 M3.00\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a flow diagram tracing the path of the solute from stock bottle to volumetric flask to titration flask.

  • Check whether your titrated sample represents the entire solution or just an aliquot before computing stock values.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the stoichiometric ratio by multiplying the moles of NaOH by 2 instead of dividing by 2, resulting in a stock concentration that is four times too high.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(NaOH)=0.1040 M×0.02885 L=0.0030004 moln(\ce{NaOH}) = 0.1040\text{ M} \times 0.02885\text{ L} = 0.0030004\text{ mol}

  2. Step 2

    n(HX2SOX4 in 25.00 mL)=0.0030004 mol×2=0.0060008 moln(\ce{H2SO4}\text{ in } 25.00\text{ mL}) = 0.0030004\text{ mol} \times 2 = 0.0060008\text{ mol}

    Correct

    n(HX2SOX4 in 25.00 mL)=0.0030004 mol×1 mol HX2SOX42 mol NaOH=0.0015002 moln(\ce{H2SO4}\text{ in } 25.00\text{ mL}) = 0.0030004\text{ mol} \times \frac{1\text{ mol }\ce{H2SO4}}{2\text{ mol }\ce{NaOH}} = 0.0015002\text{ mol}

    From the balanced equation HX2SOX4+2 NaOH→NaX2SOX4+2 HX2O\ce{H2SO4 + 2NaOH -> Na2SO4 + 2H2O}, each mole of sulfuric acid requires two moles of sodium hydroxide. You need to divide the moles of NaOH\ce{NaOH} by 22, not multiply.

  3. Step 3

    M(diluted HX2SOX4)=0.0060008 mol0.02500 L=0.2400 MM(\text{diluted }\ce{H2SO4}) = \frac{0.0060008\text{ mol}}{0.02500\text{ L}} = 0.2400\text{ M}

    Correct

    M(diluted HX2SOX4)=0.0015002 mol0.02500 L=0.06001 MM(\text{diluted }\ce{H2SO4}) = \frac{0.0015002\text{ mol}}{0.02500\text{ L}} = 0.06001\text{ M}

    Your molarity formula setup was correct, but the result carried over the incorrect mole value from Step 2.

  4. Step 4

    M(stock)=0.2400 M×(250.0 mL5.00 mL)=12.0 MM(\text{stock}) = 0.2400\text{ M} \times \left(\frac{250.0\text{ mL}}{5.00\text{ mL}}\right) = 12.0\text{ M}

    Correct

    M(stock)=0.06001 M×(250.0 mL5.00 mL)=3.00 MM(\text{stock}) = 0.06001\text{ M} \times \left(\frac{250.0\text{ mL}}{5.00\text{ mL}}\right) = 3.00\text{ M}

    Your dilution scaling factor was completely correct, but using the doubled molarity led to a final stock concentration of 12.0 M12.0\text{ M} instead of 3.00 M3.00\text{ M}.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the total moles of titrant NaOH\ce{NaOH} used accurately.

You set up the concentration and dilution factor calculations correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Stoichiometric ratio inverted

You set up dimensional analysis upside-down when converting moles of titrant to moles of analyte.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the stoichiometric coefficients between analyte and titrant. In a 1:21:2 acid-to-base reaction, 1 mol HX2SOX4=2 mol NaOH1\text{ mol }\ce{H2SO4} = 2\text{ mol }\ce{NaOH}, meaning n(HX2SOX4)=12n(NaOH)n(\ce{H2SO4}) = \frac{1}{2} n(\ce{NaOH}). Multiplying by 22 implies that one mole of base neutralizes two moles of diprotic acid.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis Check
  • Always write full units and species: mol NaOH×1 mol HX2SOX42 mol NaOH\text{mol }\ce{NaOH} \times \frac{1\text{ mol }\ce{H2SO4}}{2\text{ mol }\ce{NaOH}}.

  • Ensure the unwanted unit (mol NaOH\text{mol }\ce{NaOH}) cancels in the denominator.

Reasonableness Check
  • Since each diprotic acid molecule donates two protons, you need fewer moles of acid than of monoacidic base to react completely.

  • Verify that n(HX2SOX4)<n(NaOH)n(\ce{H2SO4}) < n(\ce{NaOH}) before calculating molarity.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. n(HX2SOX4 in 25.00 mL)=0.0030004 mol NaOH2=0.0015002 mol HX2SOX4n(\ce{H2SO4}\text{ in } 25.00\text{ mL}) = \frac{0.0030004\text{ mol }\ce{NaOH}}{2} = 0.0015002\text{ mol }\ce{H2SO4}

  2. M(dilute)=0.0015002 mol0.02500 L=0.060008 MM(\text{dilute}) = \frac{0.0015002\text{ mol}}{0.02500\text{ L}} = 0.060008\text{ M}

  3. M(stock)=0.060008 M×250.0 mL5.00 mL=3.0004 M≈3.00 MM(\text{stock}) = 0.060008\text{ M} \times \frac{250.0\text{ mL}}{5.00\text{ mL}} = 3.0004\text{ M} \approx 3.00\text{ M}

Final answer

3.00 M3.00\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out complete stoichiometric conversion factors with chemical formulas so units cancel explicitly.

  • Check that the calculated moles of a polyprotic analyte are smaller than the moles of a monoprotic titrant used.

Lock it in

Similar question

01

A 20.00 mL20.00\text{ mL} aliquot of an unknown barium hydroxide solution, Ba(OH)X2(aq)\ce{Ba(OH)2(aq)}, is neutralized by 18.40 mL18.40\text{ mL} of 0.1500 M HCl0.1500\text{ M HCl}. What is the molarity of the Ba(OH)X2\ce{Ba(OH)2} solution?

Answer

0.06900 M0.06900\text{ M}. Key steps: n(HCl)=0.1500 M×0.01840 L=2.760×10−3 moln(\ce{HCl}) = 0.1500\text{ M} \times 0.01840\text{ L} = 2.760 \times 10^{-3}\text{ mol}. From Ba(OH)X2+2 HCl→BaClX2+2 HX2O\ce{Ba(OH)2 + 2HCl -> BaCl2 + 2H2O}, n(Ba(OH)X2)=12n(HCl)=1.380×10−3 moln(\ce{Ba(OH)2}) = \frac{1}{2} n(\ce{HCl}) = 1.380 \times 10^{-3}\text{ mol}. Then M=1.380×10−3 mol0.02000 L=0.06900 MM = \frac{1.380 \times 10^{-3}\text{ mol}}{0.02000\text{ L}} = 0.06900\text{ M}.

02

A chemist dilutes 10.00 mL10.00\text{ mL} of a stock oxalic acid solution (diprotic, HX2CX2OX4\ce{H2C2O4}) to 100.0 mL100.0\text{ mL} with water. A 25.00 mL25.00\text{ mL} sample of this diluted solution requires 20.00 mL20.00\text{ mL} of 0.1250 M NaOH0.1250\text{ M NaOH} to reach the endpoint. Determine the molarity of the original stock oxalic acid solution.

Answer

0.5000 M0.5000\text{ M}. Key steps: n(NaOH)=0.1250 M×0.02000 L=2.500×10−3 moln(\ce{NaOH}) = 0.1250\text{ M} \times 0.02000\text{ L} = 2.500 \times 10^{-3}\text{ mol}. Ratio is 1:21:2, so n(HX2CX2OX4)=1.250×10−3 moln(\ce{H2C2O4}) = 1.250 \times 10^{-3}\text{ mol}. Diluted molarity Mdilute=1.250×10−3 mol0.02500 L=0.05000 MM_{\text{dilute}} = \frac{1.250 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.05000\text{ M}. Stock molarity Mstock=0.05000 M×100.0 mL10.00 mL=0.5000 MM_{\text{stock}} = 0.05000\text{ M} \times \frac{100.0\text{ mL}}{10.00\text{ mL}} = 0.5000\text{ M}.

03

A concentrated phosphoric acid (HX3POX4\ce{H3PO4}) stock solution is analyzed. First, 2.00 mL2.00\text{ mL} of stock acid is diluted to 500.0 mL500.0\text{ mL}. Then, 20.00 mL20.00\text{ mL} of this diluted solution is titrated with 0.0800 M NaOH0.0800\text{ M NaOH}, requiring 31.20 mL31.20\text{ mL} to completely neutralize all three protons according to HX3POX4+3 NaOH→NaX3POX4+3 HX2O\ce{H3PO4 + 3NaOH -> Na3PO4 + 3H2O}. Calculate the molar concentration of the concentrated stock HX3POX4\ce{H3PO4}.

Answer

10.4 M10.4\text{ M}. Key steps: n(NaOH)=0.0800 M×0.03120 L=2.496×10−3 moln(\ce{NaOH}) = 0.0800\text{ M} \times 0.03120\text{ L} = 2.496 \times 10^{-3}\text{ mol}. Triprotic ratio gives n(HX3POX4)=2.496×10−3 mol3=8.320×10−4 moln(\ce{H3PO4}) = \frac{2.496 \times 10^{-3}\text{ mol}}{3} = 8.320 \times 10^{-4}\text{ mol}. Concentration of diluted acid Mdilute=8.320×10−4 mol0.02000 L=0.04160 MM_{\text{dilute}} = \frac{8.320 \times 10^{-4}\text{ mol}}{0.02000\text{ L}} = 0.04160\text{ M}. Stock concentration Mstock=0.04160 M×(500.0 mL2.00 mL)=10.4 MM_{\text{stock}} = 0.04160\text{ M} \times \left(\frac{500.0\text{ mL}}{2.00\text{ mL}}\right) = 10.4\text{ M}.

Loading workspace…