Resources
An environmental testing laboratory receives a groundwater sample containing calcium ions at a concentration of (where ). An analyst pipettes of this sample and dilutes it with pure water to a final volume of . Given the molar mass of calcium is , calculate the final molar concentration of calcium ions, expressed in millimoles per liter ().
Answer and steps
Final answer
Steps
Determine the mass concentration after dilution
The problem states that , so the initial concentration of calcium ions () is:
When a solution is diluted by adding pure water, the total amount of solute remains constant. Applying the dilution formula:
Substitute the given volumes ( and ):
Convert mass concentration to molar concentration
Molar concentration requires expressing the amount of solute in millimoles () per liter ().
Using the molar mass of calcium ():
Therefore, of calcium has a mass of .
Divide the mass concentration by the molar mass:
Round to the correct number of significant figures
- has three significant figures.
- , , and the molar mass () each have four significant figures.
The final result is limited by the least precise measurement ( significant figures):
Typical errors
01 The student inverted the dilution ratio by multiplying by final volume over initial volume instead of initial over final volume, yielding an impossible increase in concentration upon dilution.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
From the conservation of solute, , which rearranges to . You multiplied by instead of , making the solution over twelve times more concentrated rather than diluted.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly translated the parts-per-million concentration into milligrams per liter.
You properly converted mass concentration to molar concentration using the molar mass of calcium.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou solved the dilution equation algebraically as instead of isolating , overlooking the physical reality that diluting a solution by adding water must always lower its concentration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Isolating Variables in Dilution
Because solute amount is conserved (), solving for the diluted concentration requires dividing both sides by : .
Write out the base formula explicitly and show the division step before substituting values.
- Sanity Check for Dilution
Adding solvent always increases total volume () and decreases solute concentration ().
Always check whether the volume ratio factor is less than 1 when diluting; if your final concentration is higher than your initial concentration, your volume ratio is upside down.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the dilution formula: .
Isolate the target variable: .
Substitute , , and : .
Round to three significant figures based on .
02 The student forgot to convert the initial concentration from mass units (mg/L) to molarity using the molar mass of calcium, reporting the diluted mass concentration as millimoles per liter.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Your numerical value of represents the mass concentration in . Because of calcium has a mass of , you must divide the mass concentration by the molar mass (, or ) to convert it to molarity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the dilution formula to scale the concentration down by the dilution factor.
You performed the arithmetic accurately to get .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou changed the unit label from to without performing the required molar mass conversion.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing mass concentration () with molar concentration (), overlooking that converting from mass to moles requires dividing by molar mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the requested final units
Molar concentration requires moles (or millimoles) of solute per unit volume, whereas parts per million gives mass per unit volume.
Before writing the final answer, verify whether the target unit is a mass concentration (such as ) or an amount concentration (such as or ).
- Convert $\text{mg/L}$ to $\text{mmol/L}$
because .
Divide the diluted mass concentration by the substance's molar mass to obtain the molar concentration.
CORRECTED PATH
ACEpath Teacher's DemonstrationTake the diluted mass concentration: .
Use the molar mass of calcium () to convert to molarity: .
Round to three significant figures based on the least precise measurement ().
03 The student mistook the final volume as 270.0 mL by adding 250.0 mL of pure water to the 20.0 mL aliquot rather than treating 250.0 mL as the total diluted volume.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The problem states the sample is diluted 'to a final volume of ,' meaning the total volume after dilution is , not .
- Step 3Correct
Your dilution setup was mathematically consistent with your prior step, but the numerical answer is incorrect due to the volume error in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted as .
You accurately converted mass concentration to millimoles per liter using the molar mass of calcium.
You properly set up the inverse relationship between volume and concentration in dilution.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated as solvent added rather than the total final volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the phrasing 'diluted to a volume of...' (which gives the final total volume ) with 'diluted with... volume of solvent' (which gives added volume where ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Wording Check for Dilutions
'Dilute to ' means . 'Dilute with ' or 'add of water' means .
Always scan the preposition: 'to' indicates target final volume, while 'with' indicates added solvent volume.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the final total volume directly from the problem statement: .
Substitute the correct values into the dilution equation: .
Calculate and round to three significant figures: .
Lock it in
When a solution is diluted from an initial volume to a larger final volume , what is the correct formula to solve for the final concentration ?
. The volume factor must be less than because dilution lowers concentration.
Similar question
A chemist pipettes of a solution into a volumetric flask and adds distilled water to reach a total volume of . Calculate the final molarity of the copper(II) sulfate solution.
Answer
. Using : .
A stock solution contains fluoride ions at (). An analyst dilutes of this stock to with deionized water. Given the molar mass of fluoride is , find the final concentration of fluoride in .
Answer
. First find the diluted mass concentration: . Then convert to molarity: , rounded to three significant figures as .
A student has of . What volume of water must be added to this solution to dilute it to a concentration of ? (Assume volumes are strictly additive.)
Answer
. First calculate the required total volume: . Then subtract the initial volume to find added water: (or ).