Resources
The solubility of silver iodide, (), is enhanced in the presence of sodium thiosulfate, , by forming the bis(thiosulfato)argentate(I) ion: (). A photographic fixer bath is prepared at a concentration of of (molar mass ). Determine the molar solubility of in this fixer solution.
Answer and steps
Final answer
Steps
Calculate the Initial Concentration of Thiosulfate Ion
First, convert the concentration of sodium thiosulfate, , from to :
Using the molar mass of (), find the initial molarity of the thiosulfate ion, :
Determine the Overall Equilibrium Reaction and Constant
The dissolution of silver iodide and the subsequent complexation of silver ions occur simultaneously:
- Dissolution of :
- Formation of the complex ion:
Adding these two equilibria gives the overall dissolution-complexation reaction:
The equilibrium constant for the overall reaction is the product of and :
Set Up the Equilibrium Expression
Let represent the molar solubility of in the solution (in ):
- For every mole of that dissolves and complexes, of and of are produced.
- The process consumes of per mole of dissolved.
At equilibrium:
Substitute these expressions into the overall equilibrium constant expression:
Solve for the Molar Solubility ()
Because the expression on the right is a perfect square, take the square root of both sides:
Rearrange to solve for :
Common Pitfall: Forgetting the stoichiometric coefficient of for in both the denominator's exponent () and the consumed amount () is a frequent source of error in complex-ion solubility calculations.
Typical errors
01 The student forgets the stoichiometric coefficient of 2 when expressing the equilibrium concentration of thiosulfate, writing 0.300 - s instead of 0.300 - 2s in the denominator.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because of are consumed for every of dissolved, the equilibrium concentration of thiosulfate is , not .
- Step 4Correct
Your algebraic solving technique was carried out smoothly, but the resulting value of was affected by using instead of in the previous step (note also a minor notation slip where you wrote instead of after taking the square root).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the concentration from milligrams per milliliter to molarity.
You combined the solubility product and formation equilibria into the correct overall reaction and equilibrium constant.
You correctly included the exponent of for the thiosulfate term in the law of mass action.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally wrote in the numerator after taking the square root, though you evaluated it correctly as in the subsequent lines.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou accounted for the stoichiometric coefficient of as an exponent in the equilibrium expression, but forgot to apply it to the change in concentration () when expressing the equilibrium amount of the complexing ligand.
REASONING PATH
Your ACEpath teacher’s suggested approach- Double-check stoichiometric coefficients in ICE tables
For a reactant with coefficient and initial concentration , its equilibrium concentration is .
Always write out the 'Change' row explicitly: check that corresponds to a change of .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute into the equilibrium expression: .
Take the square root of both sides: .
Solve for : .
02 The student forgets to square the thiosulfate concentration term in the equilibrium constant expression, writing K = s^2 / (0.300 - 2s) instead of s^2 / (0.300 - 2s)^2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
In the overall balanced equation , the stoichiometric coefficient of is . This requires the concentration term to be squared in the denominator of the equilibrium expression.
- Step 3Correct
Your quadratic solution followed logically from your written equation, but it yielded an incorrect final solubility because the denominator was missing the exponent of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the initial molar concentration of sodium thiosulfate.
You correctly combined the dissolution and complex-formation reactions by multiplying their equilibrium constants.
You correctly accounted for the stoichiometry when defining the remaining thiosulfate concentration as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou remembered the factor of in the consumed reactant term , but you forgot to apply that same coefficient as the power of the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the role of stoichiometric coefficients in ICE table change lines with their role as exponents in mass-action equilibrium expressions.
REASONING PATH
Your ACEpath teacher’s suggested approach- Double-Check Law of Mass Action Powers
For any species with coefficient in a balanced equation, its concentration appears in the equilibrium quotient as .
Always write the symbolic expression with explicit superscripts before substituting algebraic terms like or .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete mass-action expression: .
Notice that both numerator and denominator are perfect squares; take the square root of both sides: .
Cross-multiply and isolate : .
Combine like terms: .
03 The student neglects the depletion of thiosulfate by assuming the change in concentration is negligible, using [S2O3^2-] ≈ 0.300 M instead of 0.300 - 2s.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Each mole of that dissolves consumes of to form , so the equilibrium concentration of thiosulfate is . Because is about of the initial concentration, neglecting this change introduces significant error.
- Step 4Correct
Your algebraic steps follow logically from your expression in Step 3, but the numerical result is inaccurate due to the omitted depletion term.
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately calculated the initial molarity of the thiosulfate solution.
You correctly multiplied and to obtain the overall equilibrium constant.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the complexing ligand concentration as constant () instead of setting up the full equilibrium expression , failing to verify whether the amount consumed () was negligible relative to the initial concentration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometry of Ligand Consumption
In the reaction , the equilibrium ligand concentration is .
Always write out the ICE table row for the ligand: before deciding whether to approximate.
- Recognizing Perfect Square Expressions
When both the numerator and denominator have exponent , taking the square root of both sides avoids any quadratic formula or unnecessary approximation.
Take directly rather than dropping .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the equilibrium relation with ligand depletion: .
Take the square root of both sides: .
Clear the denominator: .
Solve for : .
Lock it in
In the reaction , if moles of dissolve per liter from an initial ligand concentration , what is the equilibrium concentration ?
. Remember that stoichiometry applies to the change line () as well as the exponent in the expression.
Similar question
Calculate the molar solubility of () in a solution, given for is .
Answer
. Setting up the expression: . Solving gives .
Copper(I) chloride, (), dissolves in cyanide solution to form (). Find the molar solubility of in .
Answer
Overall reaction: with . Because is extremely large, essentially all is consumed: . Maximum solubility limited by ligand stoichiometry is .
Solid () is placed in ( for ). What is the equilibrium concentration of uncomplexed thiosulfate, ?
Answer
. The expression is . Solving gives . Therefore, .