Resources

A microgram-scale sensor containing a silicon chip of mass m=2.50×10−4 gm = 2.50 \times 10^{-4}\text{ g} (c=0.705 J/(g⋅∘C)c = 0.705\text{ J}/(\text{g}\cdot^\circ\text{C})) is irradiated by a high-intensity laser pulse delivering 1.41 J1.41\text{ J} of thermal energy. Calculate the theoretical temperature change ΔT\Delta T predicted solely by the simple heat equation q=mcΔTq = mc\Delta T, and identify the fundamental physical phase transition limit that invalidates this unconstrained linear calculation.

Answer and steps

Final answer

Theoretical ΔT=8.00×103 ∘C\Delta T = 8.00 \times 10^3\text{ }^\circ\text{C}; this calculation fails because silicon melts at 1, ⁣414∘C1,\!414^\circ\text{C} and vaporizes at approximately 3, ⁣265∘C3,\!265^\circ\text{C}, where latent heats of fusion (ΔHfus\Delta H_{\text{fus}}) and vaporization (ΔHvap\Delta H_{\text{vap}}) must be absorbed rather than continuing simple sensible heating.

Steps

01

Calculate the theoretical temperature change (ΔT\Delta T)

The formula for sensible heat absorption without a phase change is: q=m⋅c⋅ΔTq = m \cdot c \cdot \Delta T

Rearranging the equation to solve for ΔT\Delta T: ΔT=qm⋅c\Delta T = \frac{q}{m \cdot c}

Substitute the given values into the equation:

  • Heat absorbed: q=1.41 Jq = 1.41\text{ J}
  • Mass: m=2.50×10−4 gm = 2.50 \times 10^{-4}\text{ g}
  • Specific heat capacity: c=0.705 J/(g⋅∘C)c = 0.705\text{ J}/(\text{g}\cdot^\circ\text{C})

ΔT=1.41 J(2.50×10−4 g)⋅(0.705 J/(g⋅∘C))\Delta T = \frac{1.41\text{ J}}{(2.50 \times 10^{-4}\text{ g}) \cdot (0.705\text{ J}/(\text{g}\cdot^\circ\text{C}))}

ΔT=1.411.7625×10−4 J/∘C=8.00×103 ∘C\Delta T = \frac{1.41}{1.7625 \times 10^{-4}\text{ J}/^\circ\text{C}} = 8.00 \times 10^3\text{ }^\circ\text{C}


02

Identify the physical limitation of the linear model

The formula q=m⋅c⋅ΔTq = m \cdot c \cdot \Delta T describes sensible heating, which applies only while the material remains within a single physical state with a relatively constant specific heat capacity.

A calculated temperature rise of 8.00×103 ∘C8.00 \times 10^3\text{ }^\circ\text{C} far exceeds the phase boundary limits of silicon:

  1. Melting: Solid silicon melts at 1, ⁣414∘C1,\!414^\circ\text{C}. At this point, additional energy is absorbed as the latent heat of fusion (ΔHfus\Delta H_{\text{fus}}) to break intermolecular bonds without an increase in temperature until the solid has completely liquefied.
  2. Vaporization: Liquid silicon boils at approximately 3, ⁣265∘C3,\!265^\circ\text{C}, absorbing the latent heat of vaporization (ΔHvap\Delta H_{\text{vap}}).

Because a substantial portion of the laser's energy would be consumed by these endothermic phase transitions rather than increasing the kinetic temperature, the simple linear extrapolation q=mcΔTq = mc\Delta T breaks down and drastically overestimates the temperature of the chip.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student mistakenly converts the given mass in grams to kilograms assuming mass must always be in kilograms, resulting in an overestimated temperature change by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=2.50×10−4 g=2.50×10−7 kg  ⟹  ΔT=qmc=1.412.50×10−7×0.705m = 2.50 \times 10^{-4}\text{ g} = 2.50 \times 10^{-7}\text{ kg} \implies \Delta T = \frac{q}{mc} = \frac{1.41}{2.50 \times 10^{-7} \times 0.705}

    Correct

    m=2.50×10−4 g  ⟹  ΔT=qmc=1.41 J(2.50×10−4 g)(0.705 J/(g⋅∘C))m = 2.50 \times 10^{-4}\text{ g} \implies \Delta T = \frac{q}{mc} = \frac{1.41\text{ J}}{(2.50 \times 10^{-4}\text{ g})(0.705\text{ J}/(\text{g}\cdot^\circ\text{C}))}

    You rearranged the heat equation correctly, but you converted the mass into kilograms. Because the specific heat capacity c=0.705 J/(g⋅∘C)c = 0.705\text{ J}/(\text{g}\cdot^\circ\text{C}) is expressed per gram, the mass must be kept in grams so that the mass units cancel.

  2. Step 2

    ΔT=8.00×106 ∘C\Delta T = 8.00 \times 10^6\text{ }^\circ\text{C}

    Correct

    ΔT=8.00×103 ∘C\Delta T = 8.00 \times 10^3\text{ }^\circ\text{C}

    Your arithmetic followed directly from your substituted values, but the result is 10310^3 times too large due to the unit mismatch in Step 1.

  3. Step 3

    Melting of the silicon chip into liquid.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and rearranged the heat equation to solve for ΔT\Delta T.

You correctly identified that the melting phase transition invalidates the simple linear temperature calculation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Mismatch

You converted mass from grams to kilograms even though specific heat capacity was provided in terms of grams.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that mass must always be converted to standard SI base units (kg\text{kg}) without checking whether the denominator of the specific heat capacity unit requires grams or kilograms.

REASONING PATH
Your ACEpath teacher’s suggested approach
Inspect the specific heat units
  • In q=mcΔTq = mc\Delta T, the unit of mm must match the mass unit embedded in cc.

  • Check whether cc has units of J/(g⋅∘C)\text{J}/(\text{g}\cdot^\circ\text{C}) or J/(kg⋅∘C)\text{J}/(\text{kg}\cdot^\circ\text{C}) before converting mass.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Keep the mass in grams: m=2.50×10−4 gm = 2.50 \times 10^{-4}\text{ g}.

  2. Substitute values with matching units: ΔT=1.41 J(2.50×10−4 g)⋅(0.705 J/(g⋅∘C))\Delta T = \frac{1.41\text{ J}}{(2.50 \times 10^{-4}\text{ g}) \cdot (0.705\text{ J}/(\text{g}\cdot^\circ\text{C}))}.

  3. Evaluate the denominator: m⋅c=1.7625×10−4 J/∘Cm \cdot c = 1.7625 \times 10^{-4}\text{ J}/^\circ\text{C}.

  4. Compute the quotient: ΔT=1.411.7625×10−4=8.00×103 ∘C\Delta T = \frac{1.41}{1.7625 \times 10^{-4}} = 8.00 \times 10^3\text{ }^\circ\text{C}.

Final answer

Theoretical ΔT=8.00×103 ∘C\Delta T = 8.00 \times 10^3\text{ }^\circ\text{C}; melting (fusion) at 1, ⁣414∘C1,\!414^\circ\text{C} and vaporization at ≈3, ⁣265∘C\approx 3,\!265^\circ\text{C} invalidate this linear calculation.

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out full dimensional units during substitution to ensure units cancel cleanly.

  • Practice verifying whether specific heat constants are tabulated per gram or per kilogram before starting calculations.

OverviewACEpath Teacher's Diagnosis

02 A student inverts the rearrangement of the heat equation as ΔT = mc / q, leading to an incorrect reciprocal temperature change.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    q=mcΔT  ⟹  ΔT=mcqq = mc\Delta T \implies \Delta T = \frac{mc}{q}

    Correct

    q=mcΔT  ⟹  ΔT=qmcq = mc\Delta T \implies \Delta T = \frac{q}{mc}

    You inverted the division when isolating ΔT\Delta T. Dividing both sides of q=mcΔTq = mc\Delta T by the product mcmc leaves ΔT=qmc\Delta T = \frac{q}{mc}.

  2. Step 2

    ΔT=2.50×10−4×0.7051.41  ⟹  ΔT=1.25×10−4 ∘C\Delta T = \frac{2.50 \times 10^{-4} \times 0.705}{1.41} \implies \Delta T = 1.25 \times 10^{-4}\text{ }^\circ\text{C}

    Correct

    ΔT=1.41 J(2.50×10−4 g)(0.705 J/(g⋅∘C))=8.00×103 ∘C\Delta T = \frac{1.41\text{ J}}{(2.50 \times 10^{-4}\text{ g})(0.705\text{ J}/(\text{g}\cdot^\circ\text{C}))} = 8.00 \times 10^3\text{ }^\circ\text{C}

    Your arithmetic was carried out correctly according to your formula, but the result is the reciprocal of the true value due to the rearranged formula in the previous step.

  3. Step 3

    Melting of the silicon chip into liquid.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct sensible heat relationship q=mcΔTq = mc\Delta T.

You accurately identified that melting into a liquid state limits the validity of simple linear heating.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
algebraic inversion error

You accidentally placed the heat added qq in the denominator instead of dividing by the thermal mass mcmc.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting the algebraic rearrangement of a product equation y=axy = ax when isolating the variable xx, confusing division by the coefficient with dividing the coefficient by the dependent variable.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate the Unknown Variable
  • To solve A=B⋅CA = B \cdot C for CC, divide both sides by BB, yielding C=ABC = \frac{A}{B}.

  • Divide both sides of q=mcΔTq = mc\Delta T by (mc)(mc) to isolate ΔT=qmc\Delta T = \frac{q}{mc}.

Dimensional Unit Check
  • Units of the isolated quantity must match the target unit: [ΔT]=[q][m][c][\Delta T] = \frac{[q]}{[m][c]}.

  • Check units: Jg⋅(J/(g⋅∘C))=∘C\frac{\text{J}}{\text{g} \cdot (\text{J}/(\text{g}\cdot^\circ\text{C}))} = ^\circ\text{C}. The inverted expression yields ∘C−1^\circ\text{C}^{-1}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Rearrange q=mcΔTq = mc\Delta T by dividing both sides by mcmc: ΔT=qmc\Delta T = \frac{q}{mc}.

  2. Substitute the given values: ΔT=1.41 J(2.50×10−4 g)(0.705 J/(g⋅∘C))\Delta T = \frac{1.41\text{ J}}{(2.50 \times 10^{-4}\text{ g})(0.705\text{ J}/(\text{g}\cdot^\circ\text{C}))}.

  3. Evaluate the denominator product: (2.50×10−4)(0.705)=1.7625×10−4 J/∘C(2.50 \times 10^{-4})(0.705) = 1.7625 \times 10^{-4}\text{ J}/^\circ\text{C}.

  4. Compute the quotient: ΔT=1.411.7625×10−4=8.00×103 ∘C\Delta T = \frac{1.41}{1.7625 \times 10^{-4}} = 8.00 \times 10^3\text{ }^\circ\text{C}.

Final answer

Theoretical ΔT=8.00×103 ∘C\Delta T = 8.00 \times 10^3\text{ }^\circ\text{C}; melting at 1, ⁣414∘C1,\!414^\circ\text{C} (and subsequent vaporization) absorbs latent heat, invalidating unconstrained sensible heating.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables in three-factor linear equations like q=mcΔTq = mc\Delta T and PV=nRTPV = nRT.

  • Perform a quick dimensional analysis on your isolated formula to ensure units cancel to give ∘C^\circ\text{C} rather than 1/∘C1/^\circ\text{C}.

Lock it in

Similar question

01

A sample of copper (c=0.385 J/(g⋅∘C)c = 0.385\text{ J}/(\text{g}\cdot^\circ\text{C})) has a mass of m=4.00×10−3 gm = 4.00 \times 10^{-3}\text{ g}. Calculate ΔT\Delta T when it absorbs 0.154 J0.154\text{ J} of heat.

Answer

ΔT=100∘C\Delta T = 100^\circ\text{C}. Substitute directly with mm in grams: ΔT=qmc=0.154 J(4.00×10−3 g)(0.385 J/(g⋅∘C))=0.1541.54×10−3=100∘C\Delta T = \frac{q}{mc} = \frac{0.154\text{ J}}{(4.00 \times 10^{-3}\text{ g})(0.385\text{ J}/(\text{g}\cdot^\circ\text{C}))} = \frac{0.154}{1.54 \times 10^{-3}} = 100^\circ\text{C}.

02

An aluminum heat sink (c=0.897 J/(g⋅∘C)c = 0.897\text{ J}/(\text{g}\cdot^\circ\text{C})) has a mass of 2.50 kg2.50\text{ kg}. Calculate the heat qq required to raise its temperature by 15.0∘C15.0^\circ\text{C}.

Answer

q=3.36×104 Jq = 3.36 \times 10^4\text{ J} (or 33.6 kJ33.6\text{ kJ}). Convert mass to grams to match cc: m=2.50×103 gm = 2.50 \times 10^3\text{ g}. Then q=mcΔT=(2.50×103 g)(0.897 J/(g⋅∘C))(15.0∘C)=3.36×104 Jq = mc\Delta T = (2.50 \times 10^3\text{ g})(0.897\text{ J}/(\text{g}\cdot^\circ\text{C}))(15.0^\circ\text{C}) = 3.36 \times 10^4\text{ J}.

03

A 1.00×10−3 g1.00 \times 10^{-3}\text{ g} micro-droplet of solid gallium at its melting point (29.8∘C29.8^\circ\text{C}, csolid=0.370 J/(g⋅∘C)c_{\text{solid}} = 0.370\text{ J}/(\text{g}\cdot^\circ\text{C}), ΔHfus=80.2 J/g\Delta H_{\text{fus}} = 80.2\text{ J}/\text{g}) absorbs 0.100 J0.100\text{ J} of heat. Why does calculating ΔT=qmc\Delta T = \frac{q}{mc} give an incorrect temperature, and what actually happens to the sample?

Answer

The simple formula gives ΔT=270∘C\Delta T = 270^\circ\text{C}, which is invalid because gallium is at its melting point. Melting requires qfus=m⋅ΔHfus=(1.00×10−3 g)(80.2 J/g)=0.0802 Jq_{\text{fus}} = m \cdot \Delta H_{\text{fus}} = (1.00 \times 10^{-3}\text{ g})(80.2\text{ J}/\text{g}) = 0.0802\text{ J}. The sample completely melts, and only the remaining 0.0198 J0.0198\text{ J} goes toward sensible heating of the liquid phase.

Loading workspace…