Resources
A standard laboratory protocol tests the single-replacement reaction between granulated nickel metal and dilute hydrochloric acid: .
A student adds of pure nickel powder () to of a hydrochloric acid solution with a concentration of .
(a) Confirm the reaction category. (b) Identify the limiting reactant and calculate the theoretical volume (in ) of dry hydrogen gas evolved at () and , using .
Answer and steps
Final answer
(a) Single-replacement; (b) Limiting reactant is ; theoretical volume of is .
Steps
Calculate the initial moles of each reactant
Part (a): Classifying the Reaction
A single-replacement (or single-displacement) reaction has the general form: In this reaction: Elemental nickel () replaces hydrogen () in hydrochloric acid, forming the soluble salt nickel(II) chloride () and releasing elemental hydrogen gas (). Therefore, the reaction is a single-replacement reaction.
Part (b): Determining the Limiting Reactant and Gas Volume
- Moles of nickel (): Convert the mass from milligrams to grams:
- Moles of hydrochloric acid (): Convert concentration and volume to standard units:
Identify the limiting reactant
According to the balanced chemical equation, of reacts with of .
The amount of required to react completely with of is:
Comparing the required amount to the available amount:
Because there is more present than needed, is in excess, and is the limiting reactant.
Pitfall: Do not simply compare the raw molar amounts ( vs. ) without accounting for the stoichiometric ratio. Always divide each reactant's molar quantity by its stoichiometric coefficient or calculate the required partner quantity.
Calculate the moles and volume of hydrogen gas produced
From the balanced equation, of produces of :
Using the ideal gas equation :
Substitute the given values:
Convert the theoretical volume to milliliters:
Typical errors
01 The student ignores the 1:2 stoichiometric ratio between Ni and HCl, comparing initial mole quantities directly and mistakenly identifying HCl as limiting.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
, but assuming requires : provides , while is ; if treating as with :
Correct, . Since , is the limiting reactant, giving .
You correctly found that can produce at most of , but of produces only of . The reactant that yields the smaller theoretical quantity of product is the limiting reactant, so limits the reaction, not .
- Step 4Correct
Your ideal gas calculation correctly followed from your value of , but the numerical volume and concluding statement are incorrect because they propagate the limiting reactant error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly classified the chemical reaction as a single-replacement reaction.
You accurately converted units and found the initial mole values for both nickel and hydrochloric acid.
You correctly set up and evaluated the ideal gas equation .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused which reactant limits the reaction by selecting the reactant that corresponds to the larger potential mole amount () rather than recognizing that the reactant yielding the lesser amount of product (, producing ) is consumed first.
REASONING PATH
Your ACEpath teacher’s suggested approach- Limiting Reactant Principle
The limiting reactant is the reactant that runs out first and produces the smallest theoretical amount of product.
Divide each reactant's available moles by its stoichiometric coefficient: the smaller quotient indicates the limiting reactant.
- Molar Ratio Comparison
For , needs .
Multiply moles of by 2 to see how much is required: . Since , is in excess.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare the required amount of to the available amount: .
Because , hydrochloric acid is in excess and is the limiting reactant.
Find theoretical moles of : .
Calculate theoretical volume using : .
(a) Single-replacement; (b) Limiting reactant is ; theoretical volume of is .
02 The student identifies Ni as limiting but misapplies the 1:2 mole ratio to H2, halving the moles of H2 produced instead of recognizing the 1:1 ratio between Ni and H2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Single-replacement reaction
- Step 2
- Step 3
- Step 4Correct
From the balanced chemical equation, of produces of . You divided by , likely confusing the coefficient of with the mole ratio between and .
- Step 5Correct
Your ideal gas law substitution was executed correctly, but the resulting volume is halved due to the previous molar error.
- Step 6Correct
Your final volume reflects the carried-over error in moles of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the reaction as a single-replacement reaction.
You accurately converted all laboratory quantities into moles.
You set up a sound stoichiometric comparison to identify nickel as the limiting reactant.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally divided the limiting reactant's moles by 2 when converting to the product.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou carried the stoichiometric coefficient 2 from hydrochloric acid into the conversion between nickel and hydrogen gas, overlooking the direct 1:1 molar ratio between elemental nickel and diatomic hydrogen gas.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Product Stoichiometry Directly
Mole ratios must always be taken directly from the coefficients of the two specific substances being compared: .
Write out the mole-ratio fraction explicitly: .
CORRECTED PATH
ACEpath Teacher's DemonstrationRelate the limiting reactant directly to the desired product using their stoichiometric coefficients: , so .
Calculate the theoretical gas volume using : .
Convert the volume to milliliters: .
(a) Single-replacement; (b) Limiting reactant is ; theoretical volume of is .
03 The student forgets to convert the final volume from liters to milliliters, reporting the numerical answer in liters.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Single - replacement reaction
- Step 2
- Step 3
- Step 4
- Step 5Correct
You attached the requested unit to the numerical value that was calculated in liters without performing the metric conversion ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the reaction type as a single-replacement reaction.
You converted mass and solution volume correctly to find initial mole amounts.
You used the stoichiometric mole ratio properly to deduce that nickel is the limiting reactant.
You applied the ideal gas equation accurately to determine the theoretical volume in liters.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou found the correct volume in liters () but wrote the unit as without multiplying by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the mathematical conversion factor between standard metric units and derived units when transcribing intermediate calculation results to the final stated answer.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Dimensional Consistency
, so .
Always multiply the volume obtained from (which has units of liters when using ) by to report the result in milliliters.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the volume of hydrogen gas from liters to milliliters using the conversion factor :
Round to three significant figures to match the given data: .
(a) Single-replacement; (b) Limiting reactant is ; theoretical volume of is .
Lock it in
How do you identify the limiting reactant using stoichiometric coefficients?
Divide the initial moles of each reactant by its balanced stoichiometric coefficient; the reactant with the lowest value of is limiting.
Similar question
A sample of of magnesium reacts with of hydrochloric acid according to . Identify the limiting reactant and calculate the moles of produced.
Answer
Limiting reactant: ; . Moles required: , so limits and produces .
A mass of of aluminum () is mixed with of in the reaction . Determine the limiting reactant and the theoretical moles of produced.
Answer
Limiting reactant: ; . Moles present: (ratio ), (ratio ). Since has the smaller ratio, .
In a reaction flask, of zinc powder () reacts with of via . Determine the limiting reactant and calculate the volume of dry evolved at and ().
Answer
Limiting reactant: ; . Initial moles: , . Comparing ratios: , so limits. Moles of . Volume: .