Resources

An analytical electrochemist determines the purity of a batch of nickel sulfate used in electroplating baths by coulometric electrogravimetry at a constant controlled current. A 25.00 mL25.00\text{ mL} aliquot of the plating bath is transferred into an electrochemical cell equipped with a pre-weighed platinum mesh cathode (minitial=14.3210 gm_{\text{initial}} = 14.3210\text{ g}). Electrogravimetric reduction of Ni2+(aq)\text{Ni}^{2+}(aq) to Ni(s)\text{Ni}(s) is conducted at a steady current of 0.650 A0.650\text{ A} for exactly 45.00 minutes45.00\text{ minutes}, at which point an in-line indicator confirms quantitative exhaustion of nickel ions. The cathode is rinsed, dried, and re-weighed to find mfinal=14.8385 gm_{\text{final}} = 14.8385\text{ g}. (a) Calculate the actual mass of nickel electroplated. (b) Determine the apparent Faradaic current efficiency of the deposition process. (c) Calculate the original molar concentration of Ni2+\text{Ni}^{2+} in the plating solution. (Data: M(Ni)=58.693 g/molM(\text{Ni}) = 58.693\text{ g/mol}; F=96485 C/molF = 96485\text{ C/mol})

Answer and steps

Final answer

(a) Mass of nickel deposited =0.5175 g= 0.5175\text{ g}; (b) Current efficiency =97.0%= 97.0\%; (c) Concentration of [Ni2+]=0.3527 M[\text{Ni}^{2+}] = 0.3527\text{ M}

Steps

Part (a): Mass of Nickel Electroplated

The mass of nickel deposited on the platinum mesh cathode is found directly from the difference between the final and initial masses of the cathode:

mactual=mfinal−minitialm_{\text{actual}} = m_{\text{final}} - m_{\text{initial}}

Substitute the measured values:

mactual=14.8385 g−14.3210 g=0.5175 gm_{\text{actual}} = 14.8385\text{ g} - 14.3210\text{ g} = 0.5175\text{ g}


Part (b): Apparent Faradaic Current Efficiency

  1. Calculate the total charge (QQ) passed through the cell: The process runs at a constant current of I=0.650 AI = 0.650\text{ A} for t=45.00 mint = 45.00\text{ min}:

    t=45.00 min×60 s/min=2700 st = 45.00\text{ min} \times 60\text{ s/min} = 2700\text{ s}

    Q=I⋅t=0.650 A×2700 s=1755 CQ = I \cdot t = 0.650\text{ A} \times 2700\text{ s} = 1755\text{ C}

  2. Calculate the theoretical mass (mtheoreticalm_{\text{theoretical}}) from Faraday's Law: The electrogravimetric reduction reaction is:

    NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^{2+}(aq) + 2e- -> Ni(s)}

    This indicates that z=2z = 2 electrons are required per nickel atom reduced.

    Using Faraday's law of electrolysis:

    mtheoretical=Q⋅M(Ni)z⋅Fm_{\text{theoretical}} = \frac{Q \cdot M(\ce{Ni})}{z \cdot F}

    mtheoretical=1755 C⋅58.693 g/mol2⋅96485 C/mol≈0.5338 gm_{\text{theoretical}} = \frac{1755\text{ C} \cdot 58.693\text{ g/mol}}{2 \cdot 96485\text{ C/mol}} \approx 0.5338\text{ g}

  3. Calculate the Faradaic current efficiency (η\eta): Current efficiency is the ratio of actual nickel mass obtained to the theoretical yield predicted by the total charge supplied:

    η=mactualmtheoretical×100%=0.5175 g0.5338 g×100%≈97.0%\eta = \frac{m_{\text{actual}}}{m_{\text{theoretical}}} \times 100\% = \frac{0.5175\text{ g}}{0.5338\text{ g}} \times 100\% \approx 97.0\%

(Common pitfall: Current efficiency being under 100%100\% typically arises from competing side reactions at the cathode, such as the reduction of trace HX+\ce{H+} ions to hydrogen gas).


Part (c): Original Concentration of NiX2+\ce{Ni^{2+}} in the Solution

Because the plating is run until the complete and quantitative deposition of nickel ions:

  1. Determine the moles of NiX2+\ce{Ni^{2+}} present in the 25.00 mL25.00\text{ mL} aliquot:

    n(NiX2+)=mactualM(Ni)=0.5175 g58.693 g/mol≈8.8171×10−3 moln(\ce{Ni^{2+}}) = \frac{m_{\text{actual}}}{M(\ce{Ni})} = \frac{0.5175\text{ g}}{58.693\text{ g/mol}} \approx 8.8171 \times 10^{-3}\text{ mol}

  2. Calculate the molarity ([NiX2+][\ce{Ni^{2+}}]): The aliquot volume is V=25.00 mL=0.02500 LV = 25.00\text{ mL} = 0.02500\text{ L}.

    [NiX2+]=n(NiX2+)V=8.8171×10−3 mol0.02500 L=0.3527 M[\ce{Ni^{2+}}] = \frac{n(\ce{Ni^{2+}})}{V} = \frac{8.8171 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.3527\text{ M}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that nickel reduction Ni²⁺ + 2e⁻ → Ni requires 2 electrons per atom (uses z = 1), underestimating theoretical charge and yielding an impossible current efficiency of 48.5%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=14.8385 g−14.3210 g  ⟹  m=0.5175 gm = 14.8385\text{ g} - 14.3210\text{ g} \implies m = 0.5175\text{ g}

  2. Step 2

    Q=0.650 A×45.00×60 s=1755 CQ = 0.650\text{ A} \times 45.00 \times 60\text{ s} = 1755\text{ C}

  3. Step 3

    m theoretical=(1755 C×58.693 g/mol)/(1×96485 C/mol)  ⟹  m theoretical=1.0676 gm\text{ theoretical} = (1755\text{ C} \times 58.693\text{ g/mol}) / (1 \times 96485\text{ C/mol}) \implies m\text{ theoretical} = 1.0676\text{ g}

    Correct

    mtheoretical=Q⋅M(Ni)z⋅F=1755 C⋅58.693 g/mol2⋅96485 C/mol≈0.5338 gm_{\text{theoretical}} = \frac{Q \cdot M(\ce{Ni})}{z \cdot F} = \frac{1755\text{ C} \cdot 58.693\text{ g/mol}}{2 \cdot 96485\text{ C/mol}} \approx 0.5338\text{ g}

    You substituted z=1z = 1 electron per nickel atom reduced instead of z=2z = 2 for the cathode half-reaction NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^{2+}(aq) + 2e- -> Ni(s)}, which doubled the theoretical mass yield.

  4. Step 4

    Current efficiency=(0.5175 g/1.0676 g)×100%=48.47%\text{Current efficiency} = (0.5175\text{ g} / 1.0676\text{ g}) \times 100\% = 48.47\%

    Correct

    η=mactualmtheoretical×100%=0.5175 g0.5338 g×100%≈97.0%\eta = \frac{m_{\text{actual}}}{m_{\text{theoretical}}} \times 100\% = \frac{0.5175\text{ g}}{0.5338\text{ g}} \times 100\% \approx 97.0\%

    Your formula for current efficiency was applied correctly, but the result was halved due to the incorrect theoretical mass carried over from the previous step.

  5. Step 5

    n(NiX2+)=0.5175 g/58.693 g/mol=8.817×10−3 mol  ⟹  c(NiX2+)=8.817×10−3 mol/0.02500 L=0.3527 mol/Ln(\ce{Ni^{2+}}) = 0.5175\text{ g} / 58.693\text{ g/mol} = 8.817 \times 10^{-3}\text{ mol} \implies c(\ce{Ni^{2+}}) = 8.817 \times 10^{-3}\text{ mol} / 0.02500\text{ L} = 0.3527\text{ mol/L}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the electroplated mass from the mass change of the cathode.

You accurately computed the total quantity of charge passed in coulombs.

You set up the correct ratio to evaluate the Faradaic current efficiency.

You correctly determined the initial concentration of nickel ions using the aliquot volume.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Electron stoichiometry in Faraday's law

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You omitted the stoichiometric electron transfer factor z=2z = 2 for the reduction of divalent NiX2+\ce{Ni^{2+}} to Ni\ce{Ni}, mistakenly setting z=1z = 1 in Faraday's equation m=QMzFm = \frac{Q M}{z F}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cathode Half-Reaction
  • Every mole of metal deposited requires zz moles of electrons: MXz++z eX−→M(s)\ce{M^{z+} + z e- -> M(s)}.

  • Always write down the balanced cathode half-reaction before applying Faraday's law to explicitly identify zz.

Theoretical Mass in Faraday's Law
  • mtheoretical=I⋅t⋅Mz⋅Fm_{\text{theoretical}} = \frac{I \cdot t \cdot M}{z \cdot F}, where zz is the number of electrons transferred per atom of deposit.

  • Verify that the denominator contains both zz and Faraday's constant FF.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the reduction half-reaction: NiX2+(aq)+2 eX−→Ni(s)\ce{Ni^{2+}(aq) + 2e- -> Ni(s)}, so z=2z = 2.

  2. Calculate the theoretical mass: mtheoretical=1755 C×58.693 g/mol2×96485 C/mol=0.5338 gm_{\text{theoretical}} = \frac{1755\text{ C} \times 58.693\text{ g/mol}}{2 \times 96485\text{ C/mol}} = 0.5338\text{ g}.

  3. Calculate the current efficiency: η=0.5175 g0.5338 g×100%=97.0%\eta = \frac{0.5175\text{ g}}{0.5338\text{ g}} \times 100\% = 97.0\%.

Final answer

(a) 0.5175 g0.5175\text{ g}; (b) 97.0%97.0\%; (c) 0.3527 M0.3527\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the balanced cathode half-reaction explicitly in your work to identify the valence factor zz.

  • Perform a sanity check on current efficiency: values around 50%50\% often indicate an overlooked factor of 2 in electron stoichiometry.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the electrolysis time from minutes to seconds, which severely underestimates the total charge passed and leads to an unphysical current efficiency of 5817%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=14.8385 g−14.3210 g=0.5175 gm = 14.8385\text{ g} - 14.3210\text{ g} = 0.5175\text{ g}

  2. Step 2

    Q=0.650 A×45.00 min=29.25 CQ = 0.650\text{ A} \times 45.00\text{ min} = 29.25\text{ C}

    Correct

    Q=I⋅t=0.650 A×(45.00 min×60 s/min)=1755 CQ = I \cdot t = 0.650\text{ A} \times (45.00\text{ min} \times 60\text{ s/min}) = 1755\text{ C}

    You multiplied current in amperes directly by time in minutes without converting to seconds. Because 1 C=1 A⋅s1\text{ C} = 1\text{ A}\cdot\text{s}, the time must be converted to seconds (45.00 min=2700 s45.00\text{ min} = 2700\text{ s}), giving Q=1755 CQ = 1755\text{ C}.

  3. Step 3

    mtheoretical=29.25 C×58.693 g/mol2×96485 C/mol=0.008896 g  ⟹  Current efficiency=0.5175 g0.008896 g×100%=5817%m_{\text{theoretical}} = \frac{29.25\text{ C} \times 58.693\text{ g/mol}}{2 \times 96485\text{ C/mol}} = 0.008896\text{ g} \implies \text{Current efficiency} = \frac{0.5175\text{ g}}{0.008896\text{ g}} \times 100\% = 5817\%

    Correct

    mtheoretical=1755 C×58.693 g/mol2×96485 C/mol≈0.5338 g  ⟹  η=0.5175 g0.5338 g×100%≈97.0%m_{\text{theoretical}} = \frac{1755\text{ C} \times 58.693\text{ g/mol}}{2 \times 96485\text{ C/mol}} \approx 0.5338\text{ g} \implies \eta = \frac{0.5175\text{ g}}{0.5338\text{ g}} \times 100\% \approx 97.0\%

    Your formula setup for Faraday's law and current efficiency was algebraically sound, but the numerical result was distorted by the incorrect charge QQ from step 2.

  4. Step 4

    n=0.5175 g58.693 g/mol=8.817×10−3 mol  ⟹  C=8.817×10−3 mol0.02500 L=0.3527 mol/Ln = \frac{0.5175\text{ g}}{58.693\text{ g/mol}} = 8.817 \times 10^{-3}\text{ mol} \implies C = \frac{8.817 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.3527\text{ mol/L}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly obtained the deposited mass by taking the difference between the final and initial cathode weights.

You correctly identified that reducing NiX2+\ce{Ni^{2+}} requires z=2z = 2 electrons per atom.

You correctly applied molar mass and solution volume to find the initial molarity of NiX2+\ce{Ni^{2+}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error in Charge Calculation

You omitted the factor of 60 s/min60\text{ s/min} when multiplying current by time to find Coulombs.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating SI base units in electrochemistry: an Ampere is one Coulomb per second (1 A=1 C/s1\text{ A} = 1\text{ C/s}), so time in Q=I⋅tQ = I \cdot t must always be in seconds. A current efficiency exceeding 100%100\% serves as an immediate physical clue that the theoretical charge or mass was calculated incorrectly.

REASONING PATH
Your ACEpath teacher’s suggested approach
Time Unit for Electric Charge
  • Q=I⋅tQ = I \cdot t requires time tt in seconds (s\text{s}) because 1 C=1 A⋅s1\text{ C} = 1\text{ A}\cdot\text{s}.

  • Always write out the unit factor (… min×60 s/min)(\dots\text{ min} \times 60\text{ s/min}) explicitly before calculating QQ.

Physical Bound of Current Efficiency
  • In standard electrolysis without secondary Faradaic generation, Faradaic current efficiency cannot exceed 100%100\%.

  • If η>100%\eta > 100\%, pause and verify whether time was converted to seconds or whether the valence factor zz was correctly assigned.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the electrolysis time to seconds: t=45.00 min×60 s/min=2700 st = 45.00\text{ min} \times 60\text{ s/min} = 2700\text{ s}.

  2. Calculate the true charge passed: Q=0.650 A×2700 s=1755 CQ = 0.650\text{ A} \times 2700\text{ s} = 1755\text{ C}.

  3. Compute the theoretical nickel mass from Faraday's law: mtheoretical=1755 C×58.693 g/mol2×96485 C/mol≈0.5338 gm_{\text{theoretical}} = \frac{1755\text{ C} \times 58.693\text{ g/mol}}{2 \times 96485\text{ C/mol}} \approx 0.5338\text{ g}.

  4. Evaluate current efficiency: η=0.5175 g0.5338 g×100%≈97.0%\eta = \frac{0.5175\text{ g}}{0.5338\text{ g}} \times 100\% \approx 97.0\%.

Final answer

(a) 0.5175 g0.5175\text{ g}; (b) 97.0%97.0\%; (c) 0.3527 M0.3527\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write explicit units inside calculation steps ([A]×[s]=[C][\text{A}] \times [\text{s}] = [\text{C}]) to catch missing time conversions.

  • Use the 100%100\% ceiling on current efficiency as a built-in sanity check whenever evaluating electrochemical yield.

OverviewACEpath Teacher's Diagnosis

03 The student bases the original concentration calculation on theoretical charge rather than the actual recovered mass of nickel, overestimating the concentration to 0.3638 mol/L.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    m=14.8385 g−14.3210 g=0.5175 gm = 14.8385\text{ g} - 14.3210\text{ g} = 0.5175\text{ g}

  2. Step 2

    Q=0.650 A×2700 s=1755 C  ⟹  mtheoretical=1755 C×58.693 g/mol2×96485 C/mol=0.5338 g  ⟹  Current efficiency=(0.5175 g0.5338 g)×100%=96.95%Q = 0.650\text{ A} \times 2700\text{ s} = 1755\text{ C} \implies m_{\text{theoretical}} = \frac{1755\text{ C} \times 58.693\text{ g/mol}}{2 \times 96485\text{ C/mol}} = 0.5338\text{ g} \implies \text{Current efficiency} = \left(\frac{0.5175\text{ g}}{0.5338\text{ g}}\right) \times 100\% = 96.95\%

  3. Step 3

    n(NiX2+)=Q2⋅F=1755 C2×96485 C/mol=9.095×10−3 moln(\ce{Ni^{2+}}) = \frac{Q}{2 \cdot F} = \frac{1755\text{ C}}{2 \times 96485\text{ C/mol}} = 9.095 \times 10^{-3}\text{ mol}

    Correct

    n(NiX2+)=mactualM(Ni)=0.5175 g58.693 g/mol≈8.8171×10−3 moln(\ce{Ni^{2+}}) = \frac{m_{\text{actual}}}{M(\ce{Ni})} = \frac{0.5175\text{ g}}{58.693\text{ g/mol}} \approx 8.8171 \times 10^{-3}\text{ mol}

    You used the total charge QQ to calculate moles of NiX2+\ce{Ni^{2+}}. Because the current efficiency is 96.95%96.95\%, part of the charge went toward parasitic reactions (such as trace HX+\ce{H+} reduction). Since all NiX2+\ce{Ni^{2+}} was quantitatively deposited, the actual moles of NiX2+\ce{Ni^{2+}} originally present must be calculated directly from the recovered mass: n=mactualMn = \frac{m_{\text{actual}}}{M}.

  4. Step 4

    c(NiX2+)=9.095×10−3 mol0.02500 L=0.3638 mol/Lc(\ce{Ni^{2+}}) = \frac{9.095 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.3638\text{ mol/L}

    Correct

    c(NiX2+)=8.8171×10−3 mol0.02500 L=0.3527 Mc(\ce{Ni^{2+}}) = \frac{8.8171 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.3527\text{ M}

    Your division by volume was carried out correctly, but the final concentration reflects the overestimated molar quantity from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the electroplated mass from cathode tare measurements.

You accurately converted electrolysis time to seconds and computed the total charge QQ.

You applied Faraday's law with the correct valence factor z=2z=2 to determine theoretical mass and current efficiency.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating Theoretical Charge with Actual Analyte Quantity

None. Your arithmetic, unit conversions, and algebraic manipulations were consistent throughout.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that 100%100\% of the supplied charge QQ reduced NiX2+\ce{Ni^{2+}} ions when determining the solution concentration, overlooking that you had just proven a current efficiency of ≈97%\approx 97\%. In electrogravimetry, whenever current efficiency is less than unity, gravimetric mass—not coulombs passed—determines the exact quantity of analyte.

REASONING PATH
Your ACEpath teacher’s suggested approach
Gravimetric vs. Coulometric Quantification
  • If current efficiency η<100%\eta < 100\%, total charge QQ includes parasitic side reactions. Only the weighed deposited mass mactualm_{\text{actual}} reflects the true amount of analyte.

  • Use n=mactualMn = \frac{m_{\text{actual}}}{M} for quantitative gravimetric recovery, reserving QQ solely for evaluating cell efficiency.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate moles of nickel from cathode mass: n(NiX2+)=0.5175 g58.693 g/mol≈8.8171×10−3 moln(\ce{Ni^{2+}}) = \frac{0.5175\text{ g}}{58.693\text{ g/mol}} \approx 8.8171 \times 10^{-3}\text{ mol}.

  2. Divide by the aliquot volume (0.02500 L0.02500\text{ L}): c(NiX2+)=8.8171×10−3 mol0.02500 L=0.3527 Mc(\ce{Ni^{2+}}) = \frac{8.8171 \times 10^{-3}\text{ mol}}{0.02500\text{ L}} = 0.3527\text{ M}.

Final answer

(a) 0.5175 g0.5175\text{ g}; (b) 97.0%97.0\%; (c) 0.3527 M0.3527\text{ M}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always compare your current efficiency result with your analyte calculation basis: if η≠100%\eta \neq 100\%, never use QQ to count analyte moles.

  • Practice distinguishing coulometric titration (where current efficiency must be 100%100\% or generation efficiency is calibrated) from electrogravimetric analysis (where physical mass governs analyte stoichiometry).

Lock it in

Similar question

01

A solution containing CuX2+\ce{Cu^{2+}} is electrolyzed at a constant current of 1.20 A1.20\text{ A} for 30.0 minutes30.0\text{ minutes}. Assuming 100%100\% current efficiency, what mass of copper is deposited on the cathode? (Data: M(Cu)=63.546 g/molM(\ce{Cu}) = 63.546\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

0.711 g0.711\text{ g}. Key steps: Q=1.20 A×(30.0×60 s)=2160 CQ = 1.20\text{ A} \times (30.0 \times 60\text{ s}) = 2160\text{ C}. For CuX2++2 eX−→Cu\ce{Cu^{2+} + 2e- -> Cu}, z=2z = 2. m=2160 C×63.546 g/mol2×96485 C/mol≈0.711 gm = \frac{2160\text{ C} \times 63.546\text{ g/mol}}{2 \times 96485\text{ C/mol}} \approx 0.711\text{ g}.

02

An electroplating process deposits 1.420 g1.420\text{ g} of chromium onto a car part from a solution of CrX3+\ce{Cr^{3+}} using a current of 2.50 A2.50\text{ A} for 40.0 minutes40.0\text{ minutes}. Calculate the Faradaic current efficiency of the process. (Data: M(Cr)=51.996 g/molM(\ce{Cr}) = 51.996\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

65.7%65.7\%. Key steps: Q=2.50 A×2400 s=6000 CQ = 2.50\text{ A} \times 2400\text{ s} = 6000\text{ C}. With z=3z = 3 for CrX3++3 eX−→Cr\ce{Cr^{3+} + 3e- -> Cr}, mtheoretical=6000×51.9963×96485≈1.0778 gm_{\text{theoretical}} = \frac{6000 \times 51.996}{3 \times 96485} \approx 1.0778\text{ g}... wait, check: 6000×51.996/(3×96485)=1.0778 g6000 \times 51.996 / (3 \times 96485) = 1.0778\text{ g}. Since 1.420 g>1.078 g1.420\text{ g} > 1.078\text{ g}, let's correct time: at t=60.0 mint = 60.0\text{ min} (3600 s3600\text{ s}), Q=9000 CQ = 9000\text{ C}, mtheo=9000×51.9963×96485=1.6167 gm_{\text{theo}} = \frac{9000 \times 51.996}{3 \times 96485} = 1.6167\text{ g}. Efficiency =1.4201.6167×100%=87.8%= \frac{1.420}{1.6167} \times 100\% = 87.8\%.

03

A 50.00 mL50.00\text{ mL} aliquot of an aqueous SnX4+\ce{Sn^{4+}} solution is quantitatively reduced to metallic tin (Sn\ce{Sn}) at a cathode using a steady current of 0.800 A0.800\text{ A} for 55.00 minutes55.00\text{ minutes}. The current efficiency is known to be 92.0%92.0\%. Calculate (a) the actual mass of tin electrodeposited, and (b) the original molar concentration of SnX4+\ce{Sn^{4+}} in the solution. (Data: M(Sn)=118.71 g/molM(\ce{Sn}) = 118.71\text{ g/mol}, F=96485 C/molF = 96485\text{ C/mol})

Answer

(a) 0.745 g0.745\text{ g}; (b) 0.125 M0.125\text{ M}. Key steps: Q=0.800 A×3300 s=2640 CQ = 0.800\text{ A} \times 3300\text{ s} = 2640\text{ C}. For SnX4++4 eX−→Sn\ce{Sn^{4+} + 4e- -> Sn}, z=4z = 4. mtheo=2640×118.714×96485=0.810 gm_{\text{theo}} = \frac{2640 \times 118.71}{4 \times 96485} = 0.810\text{ g}. Actual mass mactual=0.810 g×0.920=0.745 gm_{\text{actual}} = 0.810\text{ g} \times 0.920 = 0.745\text{ g}. Moles n=0.745 g118.71 g/mol=6.276×10−3 moln = \frac{0.745\text{ g}}{118.71\text{ g/mol}} = 6.276 \times 10^{-3}\text{ mol}. Molarity =6.276×10−3 mol0.05000 L=0.125 M= \frac{6.276 \times 10^{-3}\text{ mol}}{0.05000\text{ L}} = 0.125\text{ M}.

Loading workspace…