Resources
In a laboratory experiment to determine the standard molar enthalpy of reaction for the displacement: a student performs two separate dissolution runs inside an insulated, constant-pressure coffee-cup calorimeter (): • Run A: of pure () is added to of (specific heat ). The temperature rises from to via the reaction: • Run B: When of reacts with sulfuric acid according to: the standardized enthalpy change is recorded as . Assuming the total mass of the mixture in Run A is , calculate (in ) and apply Hess's Law to determine the overall displacement enthalpy (in ).
Answer and steps
Final answer
,
Steps
Calculate the heat absorbed by the calorimeter system in Run A
The total heat released by the reaction, , is absorbed by both the aqueous solution and the calorimeter:
- Temperature change ():
- Heat absorbed by the solution ():
- Heat absorbed by the calorimeter hardware ():
- Total heat absorbed:
Because heat is released by the reaction into the calorimeter under constant pressure:
Determine the molar enthalpy change
Find the amount of zinc reacted in moles:
The standard molar enthalpy of reaction is:
Apply Hess's Law to find the displacement enthalpy
The target reaction is:
We are given the two thermochemical equations:
To obtain the target reaction, keep reaction (1) as written and reverse reaction (2):
- Forward reaction (1):
- Reversed reaction (2):
Adding the two equations cancels common species ( and ):
Applying Hess's Law:
Common Pitfall: When reversing a thermochemical reaction, always reverse the sign of its . Forgetting to negate would lead to an incorrect additive sum instead of a subtraction.
Typical errors
01 The student neglected the calorimeter heat capacity C_cal when calculating the total heat released, leading to an underestimated magnitude for ΔH_A°.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You only accounted for the heat absorbed by the solution. Because the problem provides the calorimeter heat capacity (), you must also include in the total absorbed heat.
- Step 3
- Step 4Correct
Your formula and division were correct, but the value is affected by omitting in Step 2.
- Step 5Correct
Your Hess's Law algebraic relationship is completely correct, but the numerical answer is shifted by the earlier value of .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the temperature change correctly.
You accurately found the moles of limiting zinc reactant ().
You correctly derived and applied Hess's Law by recognizing that subtracting reaction B from reaction A yields the displacement target.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set and forgot to add the heat absorbed by the calorimeter hardware .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn non-ideal or calibrated calorimetry where is specified, the surroundings consist of both the solution and the calorimeter vessel, meaning .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Calorimeter Constants
If a problem explicitly provides a calorimeter heat capacity , the calorimeter absorbs heat according to .
Always write before substituting numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the calorimeter hardware heat: .
Sum both heat terms: , so .
Recalculate .
Substitute into your Hess's Law equation: .
,
02 The student omitted the negative sign for the exothermic dissolution in Run A, treating q_rxn as positive and yielding an incorrect endothermic ΔH_A°.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because the calorimeter temperature increased, heat was evolved by the system into the surroundings, so . Consequently, must be negative ().
- Step 4Correct
Your Hess's Law relationship was set up correctly, but substituting the incorrect positive value of propagated the sign error into your final result.
WHAT YOU DID WELL
Compliments from Your TeacherYou accounted for both the solution mass and calorimeter heat capacity accurately.
You calculated the molar amount of zinc reacted correctly.
You identified the correct algebraic combination of reactions for Hess's Law.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the reaction enthalpy directly to the heat gained by the calorimeter without applying the negative sign for an exothermic process.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the heat absorbed by the surroundings () with the heat change of the chemical system () when the temperature rises.
REASONING PATH
Your ACEpath teacher’s suggested approach- System vs. Surroundings Sign Convention
Whenever a reaction causes the measured temperature to rise (), mark the reaction as exothermic and ensure and are negative.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the first law of thermodynamics to determine the sign of reaction heat: .
Divide by the moles of to find : .
Substitute into your Hess's Law expression: .
03 The student added rather than subtracted the two thermochemical equations when applying Hess's Law, failing to reverse the equation for Run B.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
In the target equation, is a reactant and is a product. Because Run B has as a reactant and as a product, you must reverse reaction B, which reverses the sign of to .
WHAT YOU DID WELL
Compliments from Your TeacherYou accounted for both the solution and calorimeter hardware heat capacities when finding the total heat absorbed.
You correctly identified the reaction as exothermic and assigned the negative sign to .
You accurately determined the moles of zinc and calculated the molar enthalpy .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated Hess's Law as an automatic addition of all given reaction enthalpies without checking the positions of reactants and products relative to the target thermochemical equation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Inspect Reactant and Product Locations
Compare each intermediate reaction to the target reaction. If a species appears on the opposite side, the intermediate reaction must be reversed.
Notice that is on the left in the target reaction but on the right in Run B, requiring Run B to be reversed.
- Sign Reversal Rule
Reversing a chemical equation requires multiplying its enthalpy change by : .
Change the sign of from to before summing.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the target displacement reaction: .
Keep reaction A as written: , with .
Reverse reaction B to match target reactants and products: , with .
Add the two equations to cancel and : .
,
Lock it in
When a calorimeter has a non-negligible heat capacity , what is the complete formula for the total heat absorbed by the surroundings?
. Both the liquid and the vessel absorb heat from the reaction.
Similar question
A reaction occurs in a solution calorimeter where and . The calorimeter hardware has . If , calculate the total heat of reaction in joules.
Answer
. Key steps: ; ; .
In a neutralization experiment, of reacts with excess in of solution () inside a calorimeter (). The temperature rises by . Calculate the molar enthalpy of neutralization in .
Answer
. Key steps: . . .
Given two thermochemical equations: (1) (2) and , use Hess's Law to calculate of according to .
Answer
. Key steps: Target = . .