Resources
A student in General Chemistry Lab determines the density of an unknown crystalline mineral to be . The laboratory instructor reports that the student's measurement had a percent error of , having underestimated the actual value. Working backwards from these results, calculate the accepted theoretical density of the mineral in standard SI units of .
Answer and steps
Final answer
Steps
Calculate the accepted density ()
To find the accepted density in standard SI units (), we carry out two main steps: determine the accepted density in using the definition of percent error, and then convert those units to .
Percent error measures the accuracy of an experimental value relative to the accepted value:
Let and be the true density. Substitute the given values:
Divide both sides by :
Add to both sides:
Solve for :
Common Pitfall: A negative percent error indicates an underestimate, meaning the accepted value must be larger than the experimental value (). Do not drop the negative sign or divide by the experimental value instead of the accepted value.
Convert density to standard SI units ()
Standard SI units for density are kilograms per cubic meter (). Convert both mass and volume using fundamental conversion factors:
Therefore, the conversion factor is:
Apply this conversion to the calculated accepted density:
Rounding to three significant figures to match the given measurements ( and ):
Typical errors
01 The student divides the error by the experimental value instead of the accepted theoretical value when setting up the percent error equation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Percent error measures deviation relative to the true or accepted standard, so the denominator must be the accepted value, not the experimental value.
- Step 2Correct
Your algebraic rearrangement was carried out correctly for your written formula, but the resulting density is incorrect because it propagates the denominator error from Step 1.
- Step 3Correct
Your conversion factor () is correct, but substituting the incorrect intermediate value led to an inaccurate final density. Remember also to round to three significant figures.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted that a negative percent error corresponds to an underestimate.
You performed the unit conversion between and accurately using the correct multiplier of .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou placed the experimental value () in the denominator instead of the accepted value.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the reference base in relative error calculations. Percent error always compares the absolute discrepancy against the accepted theoretical standard, so the accepted value must serve as the base in the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Reference Base Check
Percent error is always defined relative to the theoretical truth: .
Always verify that the denominator contains the accepted or theoretical value, even when that value is the unknown variable.
- Sanity Check for Underestimates
When percent error is negative, , which means .
Check whether multiplying by or dividing by properly reflects that the accepted value must be strictly larger than the experimental measurement.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the percent error definition with the accepted value in the denominator: .
Divide by and separate terms: .
Solve for the accepted density: .
Convert to standard SI units: (rounded to 3 significant figures).
02 The student incorrectly divides by 1000 instead of multiplying by 1000 when converting density from g/cm³ to kg/m³.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
% = 100% -8.39% = 100%
- Step 2
-0.0839 = - 1 0.9161 = 2.84 = 3.1001^3
- Step 3Correct
{} = 3.1001^3 ^3 = 3.1001 1000^3 = 3.10 10^3^3
You divided by instead of multiplying by . While accounts for the numerator, the denominator has , making .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly stated and used the signed percent error formula.
You preserved the negative sign indicating an experimental underestimate.
You correctly manipulated the linear equation to find the accepted density in .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeInverting the conversion factor between and by treating density conversion as merely converting grams to kilograms while forgetting that cubic meters in the denominator bring a factor of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating single-dimension mass conversion () with composite density conversion, forgetting that converting the denominator volume () places in the numerator, yielding an overall multiplier of , not .
REASONING PATH
Your ACEpath teacher’s suggested approach- Density Conversion Relationship
Write out both mass and volume conversion factors explicitly: .
- Physical Sanity Check for Density
A cubic meter is a huge volume (), so the mass of a solid mineral occupying a cubic meter must be thousands of kilograms, never grams or fractions of a kilogram.
Compare your result against liquid water: water has . An ordinary rock or mineral must have a density greater than .
CORRECTED PATH
ACEpath Teacher's DemonstrationTake the accepted density in : .
Set up dimensional analysis with independent mass and volume factors: .
Simplify the conversion multiplier: per .
Multiply and round to 3 significant figures: .
03 The student applies the percentage as a direct discount on the experimental value by taking 8.39% of 2.84 rather than solving the percent error equation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You treated the experimental value as the base and increased it by . In chemistry, percent error is always calculated relative to the true accepted value: . Setting up the equation gives , which requires dividing by rather than multiplying by .
- Step 2Correct
Your unit conversion factor of is completely correct, but the numerical result is affected by the value calculated in Step 1. Be sure to also round your final result to three significant figures ().
WHAT YOU DID WELL
Compliments from Your TeacherYou recognized that underestimating by implies the true accepted density is greater than .
You correctly applied the conversion factor between and by multiplying by .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the measured experimental value as the reference base rather than the accepted value, applying a direct markup factor of instead of solving .
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Reference Base in Percent Error
Always place the theoretical or accepted value in the denominator as the reference quantity.
- Inverting Relative Change
If , then , not or .
Rearrange the definition algebraically before plugging in numbers: .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the definition of percent error: .
Solve for the accepted density: .
Convert to standard SI units: .
Round to three significant figures to match the given data.
Lock it in
What is the standard formula for percent error, and which value belongs in the denominator?
. The accepted (theoretical) value is always the denominator because error is measured relative to the true value.
Similar question
A student measures the boiling point of an ethanol sample as . If the percent error is , what is the accepted boiling point of the pure substance?
Answer
. Key steps: .
A chemist synthesized a compound and obtained a measured density of , representing a error over the theoretical density. Determine the theoretical density in .
Answer
. Key steps: . Multiply by to obtain .
A student measures the volume of a metal cylinder by water displacement and calculates its density as . The known metal has an accepted density of . Calculate the student's percent error and state whether the measurement was an underestimate or an overestimate.
Answer
(underestimate). Key steps: Convert accepted density to : . Compute . The negative sign indicates an underestimate.