Resources
A student in an analytical chemistry laboratory performs a standardization titration to quantify the acetylsalicylic acid (, monoprotic weak acid, molar mass ) content in an analgesic tablet. A crushed tablet weighing is dissolved in an ethanol-water mixture and titrated with standardized using a calibrated buret: . The initial buret reading is and the final buret reading at the phenolphthalein endpoint is . Calculate the mass of acetylsalicylic acid in the tablet and determine its mass percentage in the commercial tablet.
Answer and steps
Final answer
Mass of acetylsalicylic acid ; Mass percentage
Steps
Determine the volume of titrant used
Calculate the volume delivered from the buret by subtracting the initial reading from the final reading:
Convert this volume to liters:
Calculate the moles of consumed
Using the molarity of the sodium hydroxide solution ():
Determine the moles and mass of acetylsalicylic acid
From the balanced neutralization reaction:
The stoichiometric ratio between acetylsalicylic acid and is . Therefore:
Calculate the mass of acetylsalicylic acid using its molar mass ():
Calculate the mass percentage of acetylsalicylic acid in the tablet
The commercial tablet has a total mass of . The mass percentage is:
Typical errors
01 The student uses the final buret reading directly as the delivered titrant volume instead of subtracting the initial reading.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You recorded the final buret reading as the volume of titrant delivered. A buret measures liquid level rather than absolute dispensed volume, so you must subtract the initial reading () from the final reading ().
- Step 2Correct
Your formula and calculation method are correct, but the result is affected by the incorrect volume carried over from Step 1.
- Step 3Correct
You correctly applied the stoichiometric ratio and multiplied by the molar mass, but this value inherits the error from Step 1.
- Step 4Correct
You set up the mass percentage ratio properly, but the final percentage is off because of the initial volume error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted milliliters to liters.
You accurately calculated moles from concentration and volume.
You correctly used the stoichiometric mole ratio between acetylsalicylic acid and .
You accurately used the molar mass to convert moles to grams and set up the mass percentage ratio.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou took the final buret reading as the dispensed volume without subtracting the initial volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating buret graduations as an absolute dispensed volume rather than measuring the difference between initial and final liquid levels ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Buret Volume Delivered
Burets are graduated from top () to bottom. The delivered titrant volume is always .
Whenever an initial buret reading is nonzero, calculate before using the volume in molarity calculations.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the delivered volume of : .
Calculate moles of : .
Apply the stoichiometric ratio to find mass of : .
Calculate the mass percentage: .
Mass of acetylsalicylic acid ; Mass percentage
02 The student forgets to convert the titrant volume from milliliters to liters before calculating moles, overestimating the molar amount by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Molarity is defined in moles per liter (). When you multiply molarity by volume in milliliters, the resulting quantity is in millimoles (), not moles. Multiplying yields .
- Step 3Correct
Your stoichiometric conversion and multiplication by the molar mass are conceptually correct, but this step carries over the factor-of-1000 error from Step 2.
- Step 4
= (413.6 / 0.4500) * 100% = 91910%
Correct= 100% 91.93%
You used the correct mass percentage formula, but the overestimated mass produced an impossible percentage exceeding .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the net volume of titrant delivered from the buret.
You correctly applied the stoichiometric mole ratio between acetylsalicylic acid and sodium hydroxide.
You correctly used the molar mass and the mass percentage formula.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated milliliters directly as liters when applying , leading to a value in millimoles that was labeled and manipulated as moles.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Consistency in Molar Calculations
Molarity () has units of . To find moles directly, volume must be in liters: .
Always write out explicit units when multiplying: if volume is in , either convert first by dividing by , or label the product as millimoles () and convert to moles before calculating grams.
- Reality Check on Mass and Percentage
The calculated mass of an analyte cannot exceed the total mass of the sample tablet, and mass percentage cannot exceed .
When you obtain a percentage greater than , pause and trace back for a missing unit conversion factor such as or .
CORRECTED PATH
ACEpath Teacher's DemonstrationMass of acetylsalicylic acid ; Mass percentage
03 The student inverts the mass percent ratio by dividing the total tablet mass by the active ingredient mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You inverted the mass percentage formula by placing the total tablet mass in the numerator and the component mass in the denominator, resulting in a percentage greater than .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the net volume of titrant accurately from the buret readings.
You used solution stoichiometry correctly to find the moles of analyte.
You converted moles to mass using the correct molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally placed the total sample mass in the numerator and the component mass in the denominator when computing the percentage.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the part and the whole in the mass percentage definition: mass percent is always , which cannot exceed for a single component.
REASONING PATH
Your ACEpath teacher’s suggested approach- Mass Percent Definition
Always place the isolated substance mass in the numerator and the initial mixture/tablet mass in the denominator.
- Sanity Check on Percentage
A component's mass percent in a mixture must be between and .
Whenever you obtain a value above , immediately verify if your fraction is inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the mass of the pure component: (or ).
Identify the total mass of the mixture (tablet): .
Substitute into the mass percent formula: .
Mass of acetylsalicylic acid ; Mass percentage
Lock it in
How do you calculate the volume of titrant delivered from a buret?
Subtract the initial buret reading from the final buret reading: .
Similar question
A sample of hydrochloric acid is titrated with . The initial buret reading is and the final buret reading is . How many moles of were delivered?
Answer
. Key steps: ; .
A sample of an unknown solid monoprotic acid is dissolved and titrated with . The buret reads at the start and at the stoichiometric point. What is the molar mass of the acid?
Answer
. Key steps: ; ; .
A antacid tablet containing diprotic magnesium hydroxide, (molar mass ), is titrated with . The titration starts at and finishes at . Calculate the mass percentage of in the tablet. Reaction: .
Answer
. Key steps: ; ; ; ; .