Resources
An aqueous solution is prepared by dissolving of non-volatile, non-electrolyte sucrose (, molar mass ) into of pure distilled water. Pure water has a normal boiling point of and a molal boiling point elevation constant of . Calculate the molality of this solution and determine its boiling point at pressure.
Answer and steps
Final answer
Molality ; Boiling Point
Steps
Calculate the moles of solute (sucrose)
Molality is defined as the number of moles of solute per kilogram of solvent. First, find the moles of sucrose () from its given mass and molar mass:
Convert the solvent mass to kilograms and find molality
The mass of the solvent (water) is given in grams and must be converted to kilograms:
Now, compute the molality ():
Calculate the boiling point elevation ()
The formula for boiling point elevation is:
Where:
- is the van 't Hoff factor. Because sucrose is a non-electrolyte, it does not dissociate in water, so .
- is the molal boiling point elevation constant ().
- is the molality ().
Substitute these values:
Common Pitfall: Unlike freezing point depression (where the temperature decreases, ), boiling point is elevated by adding a non-volatile solute, so must be added to the normal boiling point.
Determine the new boiling point ()
Add the elevation to the normal boiling point of pure water ():
Typical errors
01 The student forgets to convert the mass of the solvent from grams to kilograms when calculating molality, leading to a molality and elevation that are 1000 times too small.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Molality () requires the solvent mass in kilograms (), not grams (). Dividing by instead of made your molality times too small.
- Step 3Correct
You applied the boiling point elevation formula correctly, but your result was affected by the incorrect molality value from the previous step.
- Step 4Correct
You correctly added your calculated elevation to the normal boiling point of water, but the final temperature remained unchanged due to rounding your propagated elevation value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the amount of solute in moles.
You used the correct relationship between molal boiling point elevation constant, molality, and boiling point elevation.
You knew to add the elevation to the normal boiling point of pure water.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided the moles of solute directly by rather than converting the water mass to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the definition of molality, which specifically requires kilograms of solvent in the denominator ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Molality Unit Definition
Molality has units of , meaning solvent mass must always be expressed in kilograms.
Whenever solvent mass is given in grams, divide by before setting up the molality fraction.
- Constant Unit Matching
The constant has units of .
Ensure the denominator unit of molality () cancels the present in .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the solvent mass to kilograms: .
Calculate molality: .
Compute elevation: .
Find final boiling point: .
Molality ; Boiling Point
02 The student calculates the boiling point elevation correctly but reports ΔTb as the final boiling point instead of adding it to the normal boiling point of water.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
represents the increase in boiling point, not the boiling point itself. You need to add this elevation to pure water's normal boiling point of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the solute mass into moles using the molar mass.
You correctly expressed the mass of water in kilograms to determine molality.
You correctly recognized that sucrose has a van 't Hoff factor of and calculated the boiling point elevation .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the boiling point elevation directly to the boiling point of the solution.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisThe Greek letter indicates a change in temperature (), not the absolute temperature. Because adding a non-volatile solute elevates the boiling point, the final temperature must be higher than the pure solvent's boiling point ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Interpret Delta (Δ) Correctly
is the boiling point elevation: .
Always add to to get the solution's actual boiling point.
- Sanity Check Final Values
An aqueous solution cannot boil at under of atmospheric pressure.
Check that your final boiling point is slightly above .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecall the definition of elevation: .
Substitute pure water's boiling point and your elevation value: .
Molality ; Boiling Point
03 The student confuses boiling point elevation with freezing point depression and subtracts ΔTb from 100.00 °C instead of adding it.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
Adding a non-volatile solute elevates the boiling point, so you must add to the pure solvent's boiling point () rather than subtracting it.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the number of moles of sucrose.
You accurately converted grams of water to kilograms to determine the molality.
You applied the boiling point elevation equation with the correct constants.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou subtracted from as if calculating freezing point depression.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused boiling point elevation with freezing point depression, forgetting that adding a non-volatile solute lowers vapor pressure and therefore raises the temperature required to boil.
REASONING PATH
Your ACEpath teacher’s suggested approach- Colligative Temperature Shifts
Boiling point is elevated (), whereas freezing point is depressed ().
Always verify whether the phase transition requires more thermal energy (boiling, add ) or less thermal energy (freezing, subtract ).
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What is the defining formula and base unit for molality ()?
with units of . Solvent mass must always be in kilograms.
Similar question
A student dissolves of glucose (, molar mass ) into of water (). Calculate the molality and the boiling point of the solution at .
Answer
Molality ; Boiling point . Moles of glucose . Solvent mass . Molality . Elevation . Final .
An aqueous solution is made by dissolving of sodium chloride (, molar mass , assume ) in of water (). Find the molality of and the boiling point elevation .
Answer
Molality ; . Moles of . Solvent mass . Molality . Elevation .
A non-electrolyte sample of mass is dissolved in of water (). The measured boiling point of the solution is . Determine the molar mass of the unknown solute.
Answer
Molar mass . Elevation . Molality . Solvent mass . Moles of solute . Molar mass .