Resources
Consider the gas-phase reversible reaction: , which has an equilibrium constant of at . A rigid, sealed vessel is initially charged with of and allowed to reach dynamic chemical equilibrium at . Calculate the equilibrium molar concentration of nitrogen dioxide, , in .
Answer and steps
Final answer
Steps
Determine initial concentrations
Calculate the initial molarity of using the initial moles and the container volume:
Since no is initially present:
Set up the ICE (Initial, Change, Equilibrium) table
Let be the change in molarity of that reacts to reach equilibrium. According to the stoichiometric ratio ():
& \ce{N2O4(g)} & \rightleftharpoons & 2\,\ce{NO2(g)} \\ \text{Initial (M)} & 0.0250 & & 0 \\ \text{Change (M)} & -x & & +2x \\ \text{Equilibrium (M)} & 0.0250 - x & & 2x \end{array}$$Write the equilibrium expression and solve for
Substitute the equilibrium concentrations into the expression for :
Common Pitfall: Because is relatively large compared to the initial concentration of , the approximation is not valid ( is greater than of ). The full quadratic equation must be solved.
Rearranging into standard quadratic form :
Applying the quadratic formula :
Calculate the equilibrium concentration of
Using the equilibrium relationship :
Typical errors
01 The student forgets to square the stoichiometric coefficient of NO2 in the numerator of the equilibrium constant expression, writing x² instead of (2x)².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because of produces of , the equilibrium concentration is . Substituting this into requires squaring the entire term, yielding , rather than .
- Step 3Correct
Your quadratic solution followed correctly from your equation, but the numerical result was affected by the missing coefficient of in front of .
- Step 4Correct
You recognized the need to multiply by to find , but the value is incorrect due to the upstream error in setting up the quadratic equation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the initial concentration by dividing moles by the total volume.
You correctly stated the general equilibrium constant expression for the reaction.
You correctly recalled that when solving for the final concentration.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou represented the equilibrium concentration of as instead of in the numerator of the equilibrium constant expression.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the change in reactant () with the equilibrium molarity of a product with coefficient () leads to omitting the multiplier before applying the exponent, writing instead of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometry Appears Twice
For a species , its equilibrium concentration is , and the term in is .
Always write the full algebraic term for the species inside parentheses before applying the exponent: write , not or .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute and into : .
Rearrange into quadratic form: .
Solve for the positive root using the quadratic formula: .
Calculate .
02 The student uses moles instead of molar concentrations directly in the equilibrium constant expression without dividing by the vessel volume.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The equilibrium constant is defined in terms of molar concentrations (), not amount of substance in moles. Because the vessel volume is , the initial concentration is .
- Step 2Correct
Your algebraic manipulation and application of the quadratic formula were executed correctly, but the resulting value of was shifted because the constant term used instead of .
- Step 3Correct
You correctly multiplied by according to the stoichiometric coefficient of , but your final numerical value was affected by the initial concentration error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the stoichiometric relationship between and in the ICE table setup.
You set up the mass action expression with the correct power of for .
You rearranged your quadratic equation and applied the quadratic formula with excellent algebraic accuracy.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used the given directly in the denominator instead of dividing by the volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the vessel volume when setting up equilibrium tables. When a problem specifies moles and a container volume other than , all quantities in a calculation must first be converted to molarity ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Equilibrium Units
expressions always require molar concentrations ().
Before filling in an ICE table for , always divide initial moles by the container volume: .
- Volume Cancellation Verification
Moles can only replace concentrations in if .
Check . Because the total number of gas moles changes, volume does not cancel and directly affects equilibrium concentrations.
CORRECTED PATH
ACEpath Teacher's Demonstration03 The student solves for the reaction extent x correctly but reports x as the final equilibrium concentration of NO2 instead of 2x.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
From the balanced equation and your equilibrium setup, the equilibrium concentration of is , not . You need to multiply the calculated value of by .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the initial molar concentration from moles and volume.
You correctly represented the stoichiometric coefficient in the numerator of the equilibrium expression as .
You solved the quadratic formula accurately to find the reaction extent .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the reaction extent as the final concentration of , forgetting to multiply by the stoichiometric coefficient .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the change variable (reaction extent) with the equilibrium concentration of a species that has a stoichiometric coefficient greater than 1 ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Variable vs. Species Concentration
In an ICE table, the equilibrium concentration of a product with coefficient is .
Always re-check the 'Equilibrium' row of your ICE table before writing down the final answer to confirm whether the species concentration is , , or another multiple.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the expression for from the stoichiometry: .
Substitute your solved value into the expression: .
Multiply to calculate the final molarity: .
Lock it in
When substituting an equilibrium concentration into an expression with exponent , what is the expanded algebraic term?
. The stoichiometric coefficient affects both the multiplier inside the brackets and the exponent outside.
Similar question
For the reaction with at , an initial concentration of is placed in a rigid container. If is the molarity of that reacts, set up the equilibrium expression and solve for the equilibrium concentration of .
Answer
At equilibrium, , , and . The expression is . Taking the square root of both sides gives . Solving yields . Thus, .
Consider the dissociation in a vessel with an initial amount of of . If , determine the equilibrium concentration .
Answer
Let the change in molarity be . At equilibrium, , , and . The expression is . Rearranging into quadratic form: . Using the quadratic formula, . Thus, .
In the Haber synthesis step , a reaction vessel initially contains and . Express purely in terms of the reaction progress variable (where is the molarity of consumed) without simplifying into numerical values.
Answer
At equilibrium, , , and . Substituting into yields .