Resources
In an analytical chemistry laboratory, a student standardizes a bomb calorimeter using benzoic acid (, molar mass , known specific energy of combustion ). Combustion of a pellet of benzoic acid in excess oxygen causes the temperature of the calorimeter to rise by . In a subsequent trial, of an unknown carbohydrate powder is combusted inside the same calorimeter setup, causing a temperature rise of . Calculate: (a) the heat capacity of the calorimeter () in , and (b) the specific heat of combustion of the unknown carbohydrate in .
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Determining the Heat Capacity of the Calorimeter ()
A bomb calorimeter operates at constant volume, meaning that all thermal energy released by the combustion reaction () is absorbed by the calorimeter and its water bath ():
- Calculate the heat released by the combustion of benzoic acid: Using the mass of benzoic acid () and its known specific energy of combustion ():
- Calculate the heat absorbed by the calorimeter:
- Determine the calorimeter constant (): The heat capacity is the ratio of heat absorbed to the observed temperature increase ():
Part (b): Determining the Specific Heat of Combustion of the Unknown Carbohydrate
- Calculate the heat absorbed during the combustion of the unknown: With and :
- Determine the heat generated by the reaction:
- Calculate the specific energy of combustion (): Divide by the mass of the carbohydrate sample ():
Common Pitfall to Avoid: Pay close attention to sign conventions. A combustion reaction is exothermic, so its enthalpy or internal energy change is negative (). Forgetting the negative sign in will lead to an incorrect positive value for the energy of combustion.
Typical errors
01 The student multiplies by molar mass instead of mass because they assume the combustion value is given in kJ/mol rather than kJ/g, leading to an incorrect heat capacity of 1261 kJ/°C.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied by the molar mass (), but the given value of was already a specific energy per gram (). Checking the units shows , rather than .
- Step 2Correct
Your formula setup was entirely correct, but the calculated value was inflated because of the incorrect heat value from Step 1.
- Step 3Correct
You correctly applied the conservation of energy principle and the negative sign for an exothermic reaction, but the propagated value of affected your result.
- Step 4Correct
You correctly divided reaction heat by sample mass to find specific energy of combustion, but the final value carried over the earlier numerical error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set up the relation between heat absorbed and calorimeter heat capacity: .
You remembered that combustion is exothermic and correctly applied the negative sign in .
You correctly divided total energy by sample mass to determine the specific energy of combustion in .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou included molar mass in your calculation even though the combustion value was already provided in kilojoules per gram.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou likely assumed that standard thermodynamic combustion values must be converted through moles. When energy is already specified per gram (), multiplying directly by mass () gives the total heat release in without needing molar mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the given energy units
Specific energy is given per unit mass (); molar energy is given per mole ().
Inspect the unit of or before multiplying: use for , and for .
- Perform dimensional cancellation
All intermediate units must cancel out to yield energy units ().
Write out units explicitly: .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute heat released by benzoic acid: .
Calculate calorimeter heat capacity: .
Find heat absorbed during unknown combustion: , so .
Compute specific energy of combustion for the unknown: .
(a) ; (b)
02 The student inverts the definition of heat capacity as ΔT / q rather than q / ΔT, obtaining an erroneous calorimeter constant of 0.0968 °C/kJ and propagating it to part (b).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You inverted the formula for heat capacity by computing rather than . Notice that your calculation yields units of , even though the target unit is .
- Step 3Correct
Your formula is conceptually correct, but the result is affected by the incorrect value of from Step 2.
- Step 4Correct
You correctly applied the negative sign to account for the exothermic combustion, but the value is inaccurate due to the carried-over error in heat capacity.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly determined the heat released during the calibration reaction.
You correctly applied the negative sign to represent the exothermic energy of combustion in part (b).
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou set up heat capacity as temperature change divided by heat energy () instead of energy absorbed per degree rise (). Checking the dimensional units () directly reveals which quantity must go in the numerator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Heat Capacity Definition Check
, meaning thermal energy input divided by temperature increase.
Check that your unit is or , placing energy in the numerator.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
03 The student ignores the thermodynamic sign convention that combustion is exothermic and reports a positive specific heat of combustion of 18.71 kJ/g.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You equated directly to positive . Because combustion releases heat to the surroundings (), the reaction is exothermic and must be negative.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the heat capacity of the calorimeter using the benzoic acid calibration data.
You correctly computed the heat absorbed by the calorimeter during the unknown carbohydrate trial.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou calculated the correct magnitude () but reported it as positive instead of negative.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing system and surroundings: the calorimeter absorbs heat (), which means the chemical system releases heat ().
REASONING PATH
Your ACEpath teacher’s suggested approach- System vs. Surroundings Sign Convention
For an insulated calorimeter, energy conservation requires , so .
Always write before computing or to ensure the exothermic sign is preserved.
CORRECTED PATH
ACEpath Teacher's DemonstrationRelate the heat of reaction to the heat absorbed by the calorimeter: .
Divide by the mass of the carbohydrate sample: .
(a) ; (b)
Lock it in
How do you calculate total heat () from sample mass () when energy of combustion is given in versus ?
If in , use ; if in , first convert mass to moles: .
Similar question
A bomb calorimeter is calibrated by burning of benzoic acid (specific energy of combustion ), causing a temperature increase of . Calculate the calorimeter constant in .
Answer
. Key steps: ; .
A calorimeter with experiences a temperature rise of upon burning of a solid fuel. Determine the specific energy of combustion of the fuel in .
Answer
. Key steps: ; ; .
A sample of sucrose (, molar mass ) is burned in a bomb calorimeter (), producing a temperature rise of . Calculate both the specific energy of combustion (in ) and the molar heat of combustion (in ).
Answer
Specific energy ; Molar heat . Key steps: ; ; .