Resources
The industrial synthesis of styrene () via endothermic catalytic dehydrogenation of ethylbenzene () proceeds as (). Superheated steam is co-injected with ethylbenzene to supply latent heat, maintain catalyst activity, and suppress coking. The boundary operational constraint dictates that the endothermic reaction cools the vapor stream, but the catalyst deactivates irreversibly if the local temperature drops below . Given that the mixed feed enters at , the molar heat capacity of the hydrocarbon stream is , and the steam heat capacity is , determine the minimum steam-to-ethylbenzene molar ratio () required to achieve a single-pass conversion threshold of exactly without letting the exit temperature drop below . (Assume heat of reaction is constant over the range and heat capacities are invariant).
Answer and steps
Final answer
.
Steps
Basis and Reaction Enthalpy Requirement
Consider a basis of of ethylbenzene feed entering the reactor, with of superheated steam, where .
The catalytic dehydrogenation reaction is:
For a fractional conversion of , the amount of ethylbenzene reacted is:
The endothermic heat absorbed by the chemical reaction is:
Maximum Allowable Temperature Drop
The feed enters at and cannot fall below the catalyst deactivation threshold of .
The maximum allowable temperature decrease () across the reactor bed is:
Adiabatic Energy Balance
In an industrial adiabatic dehydrogenation reactor, no external heat is added along the catalyst bed. The enthalpy required by the endothermic reaction is supplied entirely by the sensible heat released as the flowing gas mixture cools:
Equating the required reaction heat to the sensible heat released by the cooling stream:
Substitute the given heat capacities and values:
Solving for the Steam-to-Hydrocarbon Ratio ()
Divide both sides by the temperature drop :
Subtract the hydrocarbon heat capacity contribution:
Solve for :
To strictly ensure that the exit temperature does not fall below under the operating constraint, rounding conservatively to the required operational specification yields:
Typical errors
01 The student forgets to account for the single-pass conversion of 60.0% and assumes 100% of the ethylbenzene reacts.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You calculated the endothermic heat duty for complete () conversion of ethylbenzene. Because the process only converts of the feed (), only reacts per mole of feed, requiring .
- Step 3Correct
Your algebraic setup for balancing sensible heat loss against reaction heat absorption was methodologically sound, but your numbers were shifted by the incorrect reaction heat duty from Step 2.
- Step 4Correct
Your final numerical ratio followed correctly from your prior equations, but it is too high due to neglecting the fractional conversion.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the allowable temperature drop of based on the feed and catalyst deactivation temperatures.
You correctly constructed the adiabatic heat balance equating stream heat capacity times temperature drop to the endothermic reaction enthalpy.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the molar feed amount as the amount reacted, overlooking the fact that reaction enthalpy duty in a continuous reactor scales strictly with fractional conversion: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Scaling Reaction Heat by Fractional Conversion
For a feed of moles with single-pass conversion , the extent of reaction is , and the enthalpy requirement is .
Always check whether the reaction achieves complete conversion or operates at a specified partial conversion threshold before evaluating .
- Adiabatic Thermal Invariance
Sensible heat released by the entire flowing mass equals the heat absorbed by only the reacting portion: .
Differentiate between the total mass flowing through the reactor (which provides thermal inertia) and the fraction that undergoes chemical conversion.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the moles of ethylbenzene reacted per mole of feed: .
Compute the endothermic reaction heat: .
Equate sensible heat loss to : .
Solve for : .
Minimum molar ratio
02 The student mistakenly assumes steam supplies all sensible heat, omitting the sensible heat contribution from the ethylbenzene stream.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You assumed steam provides all the sensible heat. The cooling hydrocarbon stream also cools by and releases sensible heat according to its own heat capacity ().
- Step 4Correct
Because the ethylbenzene sensible heat was omitted from the balance in Step 3, your final calculated molar ratio is higher than the actual required minimum.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the endothermic reaction enthalpy requirement from the given fractional conversion.
You correctly determined the allowable reactor temperature drop across the catalyst bed.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual modeling omission rather than an arithmetic slip.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou set up the adiabatic thermal balance as if steam were the only flowing fluid releasing sensible heat, forgetting that all entering feed components (including the ethylbenzene itself) cool together from the inlet temperature to the outlet temperature.
REASONING PATH
Your ACEpath teacher’s suggested approach- Complete Stream Heat Capacity
In an adiabatic reactor with a mixed feed, the total sensible heat released is .
Always account for every chemical species in the flowing mixture when balancing sensible heat against reaction enthalpy.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the ethylbenzene heat capacity in the sensible heat term:
Substitute the known values on a ethylbenzene basis:
Divide by :
Subtract and solve for :
03 The student converts temperatures from Celsius to Kelvin incorrectly when calculating the temperature drop, mistakenly adding 273.15 to the difference.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You converted the individual temperatures to Kelvin correctly, but then you added again to the difference. A change of is identical to a change of , so .
- Step 3Correct
You set up the sensible heat balance equation properly, but substituting the incorrect value of propagated downstream and produced an impossible negative molar ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the total endothermic heat absorbed by the reacting ethylbenzene.
You formulated the correct adiabatic energy balance equating reaction heat to sensible heat loss.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally added to the temperature difference after subtracting from .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated a temperature change () as an absolute temperature reading, forgetting that Celsius and Kelvin share the exact same scale degree size ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Temperature Interval Rule
For any temperature difference, because the offset cancels: .
Never add or subtract when computing or using a temperature change .
- Sanity Check for Ratios and Quantities
A molar ratio represents a physical quantity of matter and must be strictly positive.
If your energy balance gives a negative molar ratio or negative mass, immediately recheck your driving temperature drop or sign convention.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the true temperature drop: .
Set up the adiabatic heat balance: .
Substitute the known values: .
Divide by : .
Solve for : .
Lock it in
How is the thermal heat duty () calculated for a feed stream of moles with single-pass conversion and reaction enthalpy ?
. Only the fraction of feed that actually reacts consumes or generates reaction enthalpy.
Similar question
An endothermic cracking reaction ($ H_{} = +80.0\text{ kJ/mol}$$) has a hydrocarbon feed with C_{p} = 150.0/(\text{mol}$$\cdot$$\text{K})C_{p,} = 30.0/(\text{mol}$$\cdot$$\text{K})R = n_{}/n_{} = 10.0. If the maximum allowable temperature drop is $$\Delta T = 50.0\text{ K}$$, what is the maximum single-pass conversion X$ achievable adiabatically?_$$
Answer
(). Sensible heat available per mole of hydrocarbon feed is . Equating to yields .
Propane dehydrogenation to propene ($ H_{} = +124.0\text{ kJ/mol}$$) operates adiabatically with a feed mixture of 1.00\text{ mol}$$ propane (C_p = 110.0/(\text{mol}$$\cdot$$\text{K})C_p = 38.0/(\text{mol}$$\cdot$$\text{K})620.0,^\circ$$\text{C}$$ and the minimum exit temperature is 540.0,^\circ$$\text{C}$$. Determine the minimum steam-to-propane molar ratio RX = 50.0%$._
Answer
. The allowable temperature drop is . Reaction heat absorbed is . The energy balance is .
In an adiabatic ethylbenzene dehydrogenation reactor with feed conversion , the steam ratio is fixed at . If , , and , calculate the required inlet temperature in such that the exit temperature is exactly .
Answer
. Heat consumed is . Total heat capacity per mole EB is . The temperature drop is . Thus, .