Resources
In an analytical chemistry laboratory, a student standardizes a sodium hydroxide solution using primary standard potassium hydrogen phthalate (, , molar mass ). An accurately weighed sample of of pure is dissolved in of distilled water and titrated with the solution using a calibrated buret. The initial buret reading is and the final buret reading at the phenolphthalein end point is . Calculate the exact molarity of the standardized solution.
Answer and steps
Final answer
Steps
Calculate the moles of primary standard
Potassium hydrogen phthalate (, abbreviated as ) is a monoprotic acid that reacts with strong base in a stoichiometric ratio.
Using the mass of the solid sample and its molar mass:
Note: The volume of distilled water () used to dissolve the solid does not alter the total moles of acid present.
Determine the moles of consumed
The neutralization reaction is:
Since the mole ratio of to is :
Calculate the volume of titrant delivered
Subtract the initial buret reading from the final buret reading:
Convert this volume to liters:
Calculate the molarity of the solution
The molar concentration is the moles of solute divided by the total volume of solution delivered:
Rounding to four significant figures (consistent with the measured mass of and the delivered volume of ), the molarity of the standardized solution is .
Typical errors
01 The student forgets to subtract the initial buret reading and uses the final reading as the total volume of titrant.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You took the final buret reading as the total volume dispensed. Because the titration started at rather than , you need to subtract the initial reading from the final reading.
- Step 2
- Step 3
- Step 4Correct
Your division and molarity formula were set up properly, but substituting the uncorrected volume of led to an incorrect final concentration.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the moles of primary standard from its mass and molar mass.
You recognized that is a monoprotic acid that reacts with in a stoichiometric ratio.
You correctly set up the formula for molarity as moles of solute divided by liters of solution.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the final buret reading () as the total titrant volume dispensed, forgetting to subtract the initial buret reading of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating an absolute liquid level scale reading on a buret with the net volume delivered during a titration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Buret Volume Delivered Formula
Always verify whether the initial buret reading is or a non-zero value, and calculate the difference before converting to liters.
CORRECTED PATH
ACEpath Teacher's Demonstration02 The student uses the volume of water used to dissolve KHP instead of the volume of NaOH delivered from the buret.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You selected the volume of water used to dissolve the sample instead of calculating the volume of titrant delivered from the buret (). The dissolving water volume only affects the analyte solution's concentration in the flask, not the volume of titrant required to reach the equivalence point.
- Step 4Correct
You carried the incorrect volume forward into the molarity definition, yielding instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the moles of potassium hydrogen phthalate using its molar mass.
You recognized that and react in a stoichiometric ratio.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used the dissolution solvent volume () instead of computing the titrant volume delivered by the buret.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the analyte sample preparation volume in the Erlenmeyer flask with the titrant solution volume delivered from the buret when calculating titrant concentration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Titrant vs. Analyte Volume
In standardization, the molarity of the titrant is , where is the volume delivered from the buret ().
Always subtract initial from final buret readings to find the volume of the titrant solution being standardized.
- Role of Water in Primary Standard Dissolution
Adding distilled water to dissolve a weighed solid acid does not change the total moles of acid present.
Treat the volume of water used to dissolve solid primary standards as a medium for the reaction, never as a factor in calculating the titrant's concentration.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the delivered volume of : .
Use the moles of obtained from titration stoichiometry: .
Calculate molarity: .
03 The student misinterprets the chemical formula of potassium hydrogen phthalate as a diprotic acid with two titratable protons, applying an incorrect 1:2 stoichiometric ratio.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Potassium hydrogen phthalate () contains only one acidic hydrogen atom per formula unit, reacting with in a stoichiometric ratio (), not a ratio.
- Step 4Correct
Your division and significant figures were executed properly, but the result is doubled due to the stoichiometric error in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly determined the volume of titrant delivered from the buret readings.
You converted the delivered volume from milliliters to liters accurately.
You correctly computed the molar amount of primary standard from its mass and molar mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou assumed potassium hydrogen phthalate () donates two protons per mole of acid instead of one.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating the chemical formula of potassium hydrogen phthalate (), which has four ring hydrogens and one carboxylic proton, or confusing it with phthalic acid (), leading to an incorrect stoichiometric ratio instead of the correct monoprotic neutralization ratio.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Proticity of Acid Salts
Potassium hydrogen phthalate () is the mono-potassium salt of phthalic acid; one proton has already been replaced by potassium, leaving exactly one titratable proton.
Always write the balanced net ionic neutralization equation () to confirm the equivalence ratio before calculating titrant moles.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the stoichiometric ratio for the neutralization of with : .
Divide moles of by the delivered volume: .
Lock it in
How do you calculate the volume of titrant delivered from a buret?
. Burets measure liquid levels from top to bottom, so the delivered amount is always the difference between two readings.
Similar question
A student titrates a aliquot of with a standardized solution. The initial buret reading is and the final buret reading at the end point is . Calculate the molarity of the solution.
Answer
. Key steps: . Moles of . Since and react , .
A sample of primary standard potassium hydrogen phthalate (, molar mass ) is dissolved in water and titrated with barium hydroxide, . The initial buret reading is and the final reading is . Calculate the molarity of the solution. (Note: provides two hydroxide ions per formula unit).
Answer
. Key steps: . The reaction is , so . . Molarity .
In a vinegar analysis, of vinegar (containing acetic acid, ) is diluted to in a volumetric flask. A sample of this diluted vinegar is titrated with . The buret reading starts at and ends at . Determine the molarity of acetic acid in the original, undiluted vinegar.
Answer
. Key steps: Delivered volume . Moles of . Moles of acid in aliquot . Diluted molarity . Accounting for the dilution (), original concentration .