Resources
In an analytical chemistry laboratory, a student standardizes a sodium hydroxide solution by determining the density of a high-purity primary standard aqueous sodium chloride solution. A calibrated volumetric transfer pipet delivers an aliquot of the solution into a tared weighing bottle. The tare mass of the empty bottle is , and the gross mass of the bottle with solution is . (a) Calculate the experimental density of the solution in . (b) If the official CRC Handbook accepted density for this exact mass fraction of at is , calculate the percent error to four significant figures.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Experimental Density Calculation
- Determine the mass of the delivered solution: The mass of the liquid sample is found by subtracting the tare mass of the empty weighing bottle from the gross mass (bottle plus solution): Both measurements are precise to the thousandths place (), so the difference retains five significant figures.
- Calculate the experimental density: Density () is mass per unit volume: Substitute the calculated mass and the delivered volume ():
- Apply significant figure rules: The volume measurement () contains four significant figures, which limits the final quotient to four significant figures:
Part (b): Percent Error Calculation
- State the percent error formula: Percent error quantifies the deviation of an experimental result from an accepted literature value:
- Substitute the values: Using the experimental density of and the accepted value of :
- Round to four significant figures: Expressed to four significant figures as specified:
(Note: The negative sign indicates that the experimentally measured density is lower than the accepted literature value).
Typical errors
01 The student uses the gross mass of the weighing bottle and solution instead of subtracting the tare mass to find the net solution mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You divided the gross mass () by the volume without subtracting the tare mass of the empty weighing bottle (). Density requires the net mass of the liquid sample alone.
- Step 2Correct
You correctly applied the percent error formula , but your result was affected by the incorrect density value carried over from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recalled the definition of density as mass divided by volume.
You correctly set up and evaluated the percent error equation using your experimental value.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated gross mass (container plus contents) with net mass (contents only) when calculating density from gravimetric measurements.
REASONING PATH
Your ACEpath teacher’s suggested approach- Tare vs. Gross Mass
Always verify whether a given mass measurement includes the container before using it in density calculations.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the net mass of the delivered solution: .
Calculate the experimental density: .
Substitute the corrected density into the percent error equation: .
(a) ; (b)
02 The student divides by the experimental value instead of the accepted true value in the percent error denominator.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the experimental density () instead of the accepted reference value (). The accepted value represents the standard base of comparison and must always serve as the denominator.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the net mass of the delivered aliquot by tare subtraction.
You applied the density formula properly and maintained four significant figures.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated your measured value as the benchmark reference rather than anchoring the relative error against the accepted true value in the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Reference Base in Percent Error
Always place the true, literature, or accepted standard value in the denominator when calculating relative or percent error.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the accepted literature density: .
Substitute your experimental density () and the accepted value into the standard formula: .
Compute the numerator: .
Divide by and multiply by : .
Round to four significant figures as requested: .
(a) ; (b)
03 The student subtracts the volume from the net mass rather than dividing mass by volume to compute density.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Density is a ratio defined as mass divided by volume (), not mass minus volume. Subtracting two quantities with different physical dimensions ( and ) is dimensionally invalid.
- Step 3Correct
You applied the standard percent error formula correctly, but your result was thrown off because you used the incorrect density from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the mass of the liquid aliquot using tare subtraction.
You correctly recalled and structured the formula for percent error as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used subtraction instead of division when computing density from mass and volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing ratio-based physical properties with difference operations, leading to dimensional inconsistency between mass (grams) and volume (milliliters).
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Consistency Check
You can only add or subtract quantities that have identical units; to relate quantities with different units like and , use multiplication or division.
Always write out your units explicitly during calculation: yields , whereas is not physically meaningful.
- Definition of Density
Density represents mass per unit volume: .
Whenever you calculate density, set it up as a fraction with mass in the numerator and volume in the denominator.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
Lock it in
What is the relationship between gross mass, tare mass, and net mass?
. Only the net mass represents the sample itself.
Similar question
A student determines the density of an unknown organic liquid. An empty graduated cylinder has a mass of . When filled with of the liquid, the total mass is . Calculate the density of the liquid to four significant figures.
Answer
. First find the net mass: . Then divide by volume: , which rounds to .
A volumetric flask has a tare mass of . Filled with sucrose solution, its gross mass is . (a) Calculate the experimental density. (b) If the accepted density is , determine the percent error to four significant figures.
Answer
(a) ; (b) . Net mass is . Density is . Percent error is .
In a pycnometer experiment, an empty pycnometer weighs . When filled with water (density ), it weighs . When emptied, dried, and filled with an unknown oil, it weighs . Calculate the density of the unknown oil to four significant figures.
Answer
. Water mass is . Pycnometer volume is . Oil net mass is . Oil density is (using intermediate unrounded volume , ).