Resources
A buffer solution is prepared by mixing of methylamine (, ) with of hydrochloric acid () at . Calculate the of the conjugate acid methylammonium () using , and determine the resulting of the buffer mixture.
Answer and steps
Final answer
,
Steps
Calculate the of the conjugate acid
For any conjugate acid-base pair in aqueous solution at , the ionization constants are related by the autoionization constant of water, :
Rearrange to solve for :
Determine the initial amounts of the reactants
Calculate the amount in millimoles () of each species before reaction:
Account for the neutralization reaction
Hydrochloric acid is a strong acid and reacts completely with the weak base methylamine:
Set up an amount table:
- Initial: and
- Change: , , and
- After Reaction:
Pitfall: Forgetting that consumes the weak base rather than directly establishing a buffer ratio can lead to using initial concentrations instead of post-reaction equilibrium amounts.
Calculate the pH of the buffer solution
Both species reside in the same total volume (), so the ratio of molar concentrations equals the mole ratio:
Applying the Henderson–Hasselbalch equation:
First, calculate :
Since , the log term becomes zero ():
Typical errors
01 The student calculates pOH directly from the Henderson-Hasselbalch equation but mistakes pOH for pH without subtracting from 14.00.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The Henderson–Hasselbalch expression using calculates , not . Because the buffer contains a weak base and its conjugate acid in equal amounts, the solution must be basic ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used and to find the conjugate acid dissociation constant .
You found the exact molar amounts of weak base remaining and conjugate acid produced after neutralization.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou labeled the result of the buffer formula as instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the acid and base forms of the Henderson–Hasselbalch equation, leading to omitting the conversion step .
REASONING PATH
Your ACEpath teacher’s suggested approach- Pairing pH with pKa vs. pOH with pKb
while .
Always pair with , or if using , remember that the result is , which must be subtracted from at .
- Sanity Check for Buffer pH
A buffer prepared with a weak base () and comparable amounts of conjugate acid has .
Check whether your calculated matches the chemical nature of the solution before writing down your final answer.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecognize that the base-form buffer equation gives : .
Convert to at : .
,
02 The student inverts the relationship between Ka, Kb, and Kw by multiplying them instead of dividing.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied by instead of dividing. For a conjugate acid-base pair, the equilibrium constant relationship is , so .
- Step 2
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the moles of weak base and strong acid before reaction.
You accurately tracked the limiting reactant stoichiometry to determine the equilibrium mixture of and .
You used the half-equivalence condition to determine and successfully converted it to .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou inverted the mathematical relationship between , , and by setting rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the logarithmic relationship (where ) with the raw equilibrium constant product (), leading to multiplication rather than division when isolating .
REASONING PATH
Your ACEpath teacher’s suggested approach- Conjugate Acid-Base Product Rule
For any conjugate pair in water at , .
Always write down the product identity first before isolating either variable as a quotient.
- Magnitude Reality Check
A weak base with must have a very weak conjugate acid with , not .
Check that the exponents roughly satisfy .
CORRECTED PATH
ACEpath Teacher's DemonstrationStart from the fundamental product relation for a conjugate pair: .
Divide both sides by : .
Substitute the given constants: .
03 The student ignores the neutralization reaction between the weak base and strong acid, calculating pH by treating HCl as unreacted and setting pH = -log[HCl].
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
,
You treated as unreacted free acid in solution. Because is a strong acid and is a weak base, they undergo a complete neutralization reaction: . The of completely consumes of , leaving of and producing of .
- Step 3Correct
Because the neutralization reaction was omitted in Step 2, you calculated the using the unreacted acid concentration instead of applying the Henderson–Hasselbalch equation to the resulting buffer mixture.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the ion-product relationship to find the conjugate acid dissociation constant.
You calculated the total mixed volume and the moles of added hydrochloric acid accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated mixing a strong acid with a weak base as a simple dilution of strong acid, overlooking that strong acids and weak bases react completely until the limiting reactant is exhausted before establishing equilibrium.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Species Reactivity Before Equilibrium
When a strong acid is added to a weak base (or a strong base to a weak acid), a complete stoichiometric neutralization reaction occurs first.
Always write the neutralization reaction and construct an ICF (Initial-Change-Final) mole table before attempting equilibrium or pH calculations.
- Classify the Final Mixture
If the weak base is in excess over the strong acid, the final solution contains both a weak base and its conjugate acid, forming a buffer.
Use the Henderson–Hasselbalch equation with the post-reaction mole quantities.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate initial moles: , and .
React completely: . is limiting, so of reacts.
Find post-reaction amounts: , and .
Compute : .
Apply the Henderson–Hasselbalch equation: .
,
Lock it in
What does the equation calculate, and how do you obtain from it at ?
It calculates , not . Convert using .
Similar question
A buffer is prepared with ammonia (, ) and ammonium chloride () at . Calculate the of this solution.
Answer
. Key steps: ; then .
A solution containing ethylamine (, ) is mixed with of at . Calculate the final of the buffer.
Answer
. Key steps: Initial moles: , . After reaction: , . Then . Finally, (or using , ).
You need to prepare a buffer with at using methylamine (, ) and its conjugate acid . What molar ratio of is required?
Answer
. Key steps: Target . Using : . Inverting gives .