Resources

Consider the phase diagram of water (H2O\text{H}_2\text{O}), whose triple point is located at Tt=273.16 KT_t = 273.16\text{ K} (0.01∘C0.01^\circ\text{C}) and Pt=0.00603 atmP_t = 0.00603\text{ atm} (611.7 Pa611.7\text{ Pa}). At the normal melting point (T=273.15 KT = 273.15\text{ K}, P=1.000 atmP = 1.000\text{ atm}), the molar enthalpy of fusion is ΔHfus=6010 J/mol\Delta H_{\text{fus}} = 6010\text{ J/mol}, the molar volume of solid ice is Vm,solid=1.965×10−5 m3/molV_{\text{m,solid}} = 1.965 \times 10^{-5}\text{ m}^3/\text{mol}, and the molar volume of liquid water is Vm,liquid=1.802×10−5 m3/molV_{\text{m,liquid}} = 1.802 \times 10^{-5}\text{ m}^3/\text{mol}. Ice skaters rely on pressure-induced melting along the negative solid-liquid boundary. Using the Clapeyron equation dPdT=ΔHfusTΔVfus\frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}}, calculate the threshold pressure in megapascals (MPa\text{MPa}) necessary to depress the equilibrium melting point of ice to −2.00∘C-2.00^\circ\text{C} (271.15 K271.15\text{ K}), assuming ΔHfus\Delta H_{\text{fus}} and the molar volumes remain constant over this range (1 atm=1.013×105 Pa1\text{ atm} = 1.013 \times 10^5\text{ Pa}).

Answer and steps

Final answer

P=27.2 MPaP = 27.2\text{ MPa}

Steps

01

Calculate the change in molar volume upon melting (ΔVfus\Delta V_{\text{fus}})

To find the threshold pressure required to depress the melting point of ice to −2.00∘C-2.00^\circ\text{C} (271.15 K271.15\text{ K}), we apply the Clapeyron equation, which governs phase boundaries between condensed phases (solid and liquid): dPdT=ΔHfusTΔVfus\frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}}

The molar volume change during the solid-to-liquid transition is:

ΔVfus=Vm,liquid−Vm,solid\Delta V_{\text{fus}} = V_{\text{m,liquid}} - V_{\text{m,solid}}

Substitute the given values:

ΔVfus=1.802×10−5 m3/mol−1.965×10−5 m3/mol=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = 1.802 \times 10^{-5}\text{ m}^3/\text{mol} - 1.965 \times 10^{-5}\text{ m}^3/\text{mol} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}

Because liquid water is denser than ice, ΔVfus\Delta V_{\text{fus}} is negative, causing the solid–liquid equilibrium line of water to have a negative slope on a P–TP\text{--}T phase diagram.

02

Integrate the Clapeyron equation

Assuming ΔHfus\Delta H_{\text{fus}} and ΔVfus\Delta V_{\text{fus}} remain constant over the small temperature range from T1=273.15 KT_1 = 273.15\text{ K} to T2=271.15 KT_2 = 271.15\text{ K}, separate variables and integrate:

∫P1P2dP=ΔHfusΔVfus∫T1T2dTT\int_{P_1}^{P_2} dP = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \int_{T_1}^{T_2} \frac{dT}{T}

P2−P1=ΔHfusΔVfusln⁡(T2T1)P_2 - P_1 = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right)

03

Compute the pressure change (ΔP\Delta P)

Substitute the given constants into the equation:

ΔP=P2−P1=6010 J/mol−1.63×10−6 m3/molln⁡(271.15 K273.15 K)\Delta P = P_2 - P_1 = \frac{6010\text{ J/mol}}{-1.63 \times 10^{-6}\text{ m}^3/\text{mol}} \ln\left(\frac{271.15\text{ K}}{273.15\text{ K}}\right)

Calculate the logarithmic ratio:

ln⁡(271.15273.15)=ln⁡(0.99268)≈−7.349×10−3\ln\left(\frac{271.15}{273.15}\right) = \ln(0.99268) \approx -7.349 \times 10^{-3}

Now evaluate ΔP\Delta P:

ΔP=(−3.687×109 Pa)⋅(−7.349×10−3)≈2.710×107 Pa=27.10 MPa\Delta P = (-3.687 \times 10^9\text{ Pa}) \cdot (-7.349 \times 10^{-3}) \approx 2.710 \times 10^7\text{ Pa} = 27.10\text{ MPa}

04

Calculate the absolute pressure (P2P_2)

The initial pressure at the normal melting point is:

P1=1.000 atm=1.013×105 Pa≈0.10 MPaP_1 = 1.000\text{ atm} = 1.013 \times 10^5\text{ Pa} \approx 0.10\text{ MPa}

Adding this to the change in pressure:

P2=P1+ΔP=0.10 MPa+27.10 MPa=27.2 MPaP_2 = P_1 + \Delta P = 0.10\text{ MPa} + 27.10\text{ MPa} = 27.2\text{ MPa}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student subtracts liquid volume from solid volume when calculating ΔV_fus, leading to an incorrect positive volume change and a negative final pressure.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔVfus=Vsolid−Vliquid=1.965×10−5−1.802×10−5  ⟹  1.63×10−6 m3/mol\Delta V_{\text{fus}} = V_{\text{solid}} - V_{\text{liquid}} = 1.965 \times 10^{-5} - 1.802 \times 10^{-5} \implies 1.63 \times 10^{-6}\text{ m}^3/\text{mol}

    Correct

    ΔVfus=Vm,liquid−Vm,solid=1.802×10−5 m3/mol−1.965×10−5 m3/mol=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = V_{\text{m,liquid}} - V_{\text{m,solid}} = 1.802 \times 10^{-5}\text{ m}^3/\text{mol} - 1.965 \times 10^{-5}\text{ m}^3/\text{mol} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}

    Fusion represents the phase transition from solid to liquid, so the change in molar volume is defined as final state minus initial state: ΔVfus=Vm,liquid−Vm,solid\Delta V_{\text{fus}} = V_{\text{m,liquid}} - V_{\text{m,solid}}. Because liquid water is denser than solid ice, ΔVfus\Delta V_{\text{fus}} must be negative.

  2. Step 2

    dPdT=ΔHfusTΔVfus  ⟹  ΔP=ΔHfusΔVfusln⁡(T2T1)\frac{dP}{dT} = \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}} \implies \Delta P = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right)

  3. Step 3

    ΔP=(60101.63×10−6)ln⁡(271.15273.15)  ⟹  −27.1 MPa\Delta P = \left(\frac{6010}{1.63 \times 10^{-6}}\right) \ln\left(\frac{271.15}{273.15}\right) \implies -27.1\text{ MPa}

    Correct

    ΔP=(6010−1.63×10−6)ln⁡(271.15273.15)≈27.1 MPa\Delta P = \left(\frac{6010}{-1.63 \times 10^{-6}}\right) \ln\left(\frac{271.15}{273.15}\right) \approx 27.1\text{ MPa}

    Your algebraic evaluation and unit conversion were executed properly, but the result carries the incorrect sign propagated from the positive ΔVfus\Delta V_{\text{fus}} in Step 1.

  4. Step 4

    P=P1+ΔP=0.1013 MPa−27.1 MPa  ⟹  −27.0 MPaP = P_1 + \Delta P = 0.1013\text{ MPa} - 27.1\text{ MPa} \implies -27.0\text{ MPa}

    Correct

    P=P1+ΔP=0.1013 MPa+27.10 MPa≈27.2 MPaP = P_1 + \Delta P = 0.1013\text{ MPa} + 27.10\text{ MPa} \approx 27.2\text{ MPa}

    You correctly added the pressure increment to the atmospheric baseline, but the negative increment resulted in an unphysical negative absolute pressure.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly selected and integrated the Clapeyron equation for condensed phase equilibrium.

You converted all temperatures accurately to kelvins and handled unit conversions to megapascals correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Reversed State Subtraction in Delta V

You set up ΔVfus\Delta V_{\text{fus}} as solid minus liquid instead of liquid minus solid.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Any thermodynamic state change ΔX\Delta X for a transition from state AA to state BB is defined as Xfinal−XinitialX_{\text{final}} - X_{\text{initial}}. Melting is a transition from solid to liquid, so ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}}. For water, liquid is denser than ice, which makes ΔVfus<0\Delta V_{\text{fus}} < 0 and explains why increasing pressure lowers the melting temperature.

REASONING PATH
Your ACEpath teacher’s suggested approach
State Transition Direction
  • For any phase change, Δ=final−initial\Delta = \text{final} - \text{initial}.

  • Always identify the direction of the phase change: fusion is solid →\to liquid, so write ΔVfus=Vliquid−Vsolid\Delta V_{\text{fus}} = V_{\text{liquid}} - V_{\text{solid}}.

Physical Reality Check on Phase Boundaries
  • If a phase boundary has a negative slope (dP/dT<0dP/dT < 0), applying pressure depresses the melting temperature, requiring ΔP>0\Delta P > 0 when T2<T1T_2 < T_1.

  • Check whether depressing the freezing point of water should require higher pressure or negative pressure; absolute pressures in phase diagrams must remain positive.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ΔVfus=Vm,liquid−Vm,solid=1.802×10−5−1.965×10−5=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = V_{\text{m,liquid}} - V_{\text{m,solid}} = 1.802 \times 10^{-5} - 1.965 \times 10^{-5} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}

  2. ΔP=6010 J/mol−1.63×10−6 m3/molln⁡(271.15 K273.15 K)≈(−3.687×109 Pa)×(−7.349×10−3)≈2.710×107 Pa=27.10 MPa\Delta P = \frac{6010\text{ J/mol}}{-1.63 \times 10^{-6}\text{ m}^3/\text{mol}} \ln\left(\frac{271.15\text{ K}}{273.15\text{ K}}\right) \approx (-3.687 \times 10^9\text{ Pa}) \times (-7.349 \times 10^{-3}) \approx 2.710 \times 10^7\text{ Pa} = 27.10\text{ MPa}

  3. P=P1+ΔP=0.1013 MPa+27.10 MPa=27.2 MPaP = P_1 + \Delta P = 0.1013\text{ MPa} + 27.10\text{ MPa} = 27.2\text{ MPa}

Final answer

P=27.2 MPaP = 27.2\text{ MPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the formal convention for transition quantities: ΔXtrans=Xfinal−Xinitial\Delta X_{\text{trans}} = X_{\text{final}} - X_{\text{initial}}.

  • Practice sketching the P–TP\text{--}T phase diagram of water to visualize why dP/dT<0dP/dT < 0 requires ΔP>0\Delta P > 0 to lower the melting temperature.

  • Complete the follow-up drills on Clapeyron phase transitions to reinforce correct sign conventions.

OverviewACEpath Teacher's Diagnosis

02 The student calculates the pressure difference ΔP correctly but forgets to add the initial atmospheric pressure of 1.000 atm to obtain the absolute threshold pressure.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔVfus=1.802×10−5−1.965×10−5=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = 1.802 \times 10^{-5} - 1.965 \times 10^{-5} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}

  2. Step 2

    ΔP=(ΔHfusΔVfusln⁡(T2T1))  ⟹  ΔP=(6010−1.63×10−6)ln⁡(271.15273.15)\Delta P = \left(\frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}}\ln\left(\frac{T_2}{T_1}\right)\right) \implies \Delta P = \left(\frac{6010}{-1.63 \times 10^{-6}}\right)\ln\left(\frac{271.15}{273.15}\right)

  3. Step 3

    ΔP=(−3.687×109)×(−0.00735)=2.71×107 Pa\Delta P = (-3.687 \times 10^9) \times (-0.00735) = 2.71 \times 10^7\text{ Pa}

  4. Step 4

    P=27.1 MPaP = 27.1\text{ MPa}

    Correct

    P2=P1+ΔP=1.013×105 Pa+2.710×107 Pa=2.72×107 Pa=27.2 MPaP_2 = P_1 + \Delta P = 1.013 \times 10^5\text{ Pa} + 2.710 \times 10^7\text{ Pa} = 2.72 \times 10^7\text{ Pa} = 27.2\text{ MPa}

    You equated the total pressure PP directly to the pressure change ΔP\Delta P, neglecting to add the initial reference pressure P1=1.000 atm≈0.10 MPaP_1 = 1.000\text{ atm} \approx 0.10\text{ MPa}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the negative molar volume change ΔVfus\Delta V_{\text{fus}} for the melting of ice.

You set up and integrated the Clapeyron equation with the correct temperature limits.

You accurately calculated the pressure difference ΔP\Delta P in pascals and converted it to megapascals.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of reference state / Confusion between absolute pressure and differential pressure

You equated the total threshold pressure P2P_2 to ΔP\Delta P rather than adding the initial pressure P1=1.000 atmP_1 = 1.000\text{ atm}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Integrating a differential relationship ∫P1P2dP=ΔP\int_{P_1}^{P_2} dP = \Delta P yields the pressure difference relative to the initial state, not the absolute pressure itself. When a question asks for the total or threshold pressure, the initial state pressure (P1=1 atm=0.1013 MPaP_1 = 1\text{ atm} = 0.1013\text{ MPa}) must be added to ΔP\Delta P.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Definite Integral Limits
  • ∫P1P2dP=P2−P1=ΔP  ⟹  P2=P1+ΔP\int_{P_1}^{P_2} dP = P_2 - P_1 = \Delta P \implies P_2 = P_1 + \Delta P

  • Always write down P2−P1P_2 - P_1 explicitly instead of just ΔP\Delta P to remind yourself that solving for P2P_2 requires adding P1P_1.

Distinguish Gauge/Differential Pressure from Absolute Pressure
  • Thermodynamic state variables on a phase diagram represent absolute values, not gauge or relative differences.

  • Check whether the question asks for an increase in pressure (ΔP\Delta P) or the absolute threshold pressure (PP). If absolute pressure is requested, convert P1P_1 to matching units and add it.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the initial condition at the normal melting point: P1=1.000 atm=1.013×105 Pa≈0.1013 MPaP_1 = 1.000\text{ atm} = 1.013 \times 10^5\text{ Pa} \approx 0.1013\text{ MPa}.

  2. Express absolute final pressure as P2=P1+ΔPP_2 = P_1 + \Delta P.

  3. Compute: P2=0.1013 MPa+27.10 MPa=27.20 MPaP_2 = 0.1013\text{ MPa} + 27.10\text{ MPa} = 27.20\text{ MPa}.

Final answer

P=27.2 MPaP = 27.2\text{ MPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • In integration problems involving physical states, explicitly write the boundary values P2−P1P_2 - P_1 on the left-hand side.

  • Ensure all pressures are converted to the same unit (MPa) before adding them together.

OverviewACEpath Teacher's Diagnosis

03 The student uses Celsius temperatures directly in the logarithmic term or temperature denominator instead of converting to Kelvin.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔVfus=1.802×10−5−1.965×10−5=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = 1.802 \times 10^{-5} - 1.965 \times 10^{-5} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}

  2. Step 2

    ΔP=(ΔHfusT×ΔVfus)ΔT⟹ΔP=(6010−2.00×(−1.63×10−6))×(−2.00)\Delta P = \left(\frac{\Delta H_{\text{fus}}}{T \times \Delta V_{\text{fus}}}\right) \Delta T \Longrightarrow \Delta P = \left(\frac{6010}{-2.00 \times (-1.63 \times 10^{-6})}\right) \times (-2.00)

    Correct

    ΔP=ΔHfusΔVfusln⁡(T2T1)=6010 J/mol−1.63×10−6 m3/molln⁡(271.15 K273.15 K)\Delta P = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right) = \frac{6010\text{ J/mol}}{-1.63 \times 10^{-6}\text{ m}^3/\text{mol}} \ln\left(\frac{271.15\text{ K}}{273.15\text{ K}}\right)

    You used T=−2.00T = -2.00 in degrees Celsius in the denominator instead of converting to absolute temperature in Kelvin (T1=273.15 KT_1 = 273.15\text{ K}, T2=271.15 KT_2 = 271.15\text{ K}). In thermodynamic equations, temperature TT must always be on the absolute Kelvin scale. Integrating the Clapeyron equation yields ΔP=ΔHfusΔVfusln⁡(T2T1)\Delta P = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right).

  3. Step 3

    ΔP=−3.69×109 Pa=−3690 MPa⟹P=0.1013−3690=−3689.9 MPa\Delta P = -3.69 \times 10^9\text{ Pa} = -3690\text{ MPa} \Longrightarrow P = 0.1013 - 3690 = -3689.9\text{ MPa}

    Correct

    P2=P1+ΔP=0.10 MPa+27.10 MPa=27.2 MPaP_2 = P_1 + \Delta P = 0.10\text{ MPa} + 27.10\text{ MPa} = 27.2\text{ MPa}

    Because of the negative temperature used in the denominator, the pressure change evaluated to −3690 MPa-3690\text{ MPa}, yielding an impossible negative absolute pressure.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the change in molar volume upon melting, ΔVfus=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}.

You recognized that the Clapeyron equation relates the change in melting temperature to the required change in pressure.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature Unit Error (Celsius instead of Kelvin)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted temperatures in degrees Celsius into the absolute thermodynamic temperature term TT, overlooking that state functions and derivative relations in thermodynamics require absolute temperature in Kelvin.

REASONING PATH
Your ACEpath teacher’s suggested approach
Absolute Temperature Requirement
  • Any thermodynamic formula featuring an isolated temperature variable TT (such as in dPdT=ΔHTΔV\frac{dP}{dT} = \frac{\Delta H}{T \Delta V}) requires temperature in Kelvin: T(K)=T(∘C)+273.15T(\text{K}) = T(^\circ\text{C}) + 273.15.

  • Always convert temperatures to Kelvin before substituting into thermodynamic equations.

Integrating the Clapeyron Equation
  • For finite temperature changes, separate variables and integrate: ∫P1P2dP=ΔHΔV∫T1T2dTT  ⟹  ΔP=ΔHΔVln⁡(T2T1)\int_{P_1}^{P_2} dP = \frac{\Delta H}{\Delta V} \int_{T_1}^{T_2} \frac{dT}{T} \implies \Delta P = \frac{\Delta H}{\Delta V} \ln\left(\frac{T_2}{T_1}\right).

  • Use the logarithmic ratio ln⁡(T2/T1)\ln(T_2/T_1) rather than approximating TT in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert both temperatures to Kelvin: T1=273.15 KT_1 = 273.15\text{ K} and T2=271.15 KT_2 = 271.15\text{ K}.

  2. Integrate the Clapeyron equation: ΔP=ΔHfusΔVfusln⁡(T2T1)\Delta P = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right).

  3. Substitute the values: ΔP=6010 J/mol−1.63×10−6 m3/molln⁡(271.15273.15)≈(−3.687×109 Pa)×(−7.349×10−3)≈27.10 MPa\Delta P = \frac{6010\text{ J/mol}}{-1.63 \times 10^{-6}\text{ m}^3/\text{mol}} \ln\left(\frac{271.15}{273.15}\right) \approx (-3.687 \times 10^9\text{ Pa}) \times (-7.349 \times 10^{-3}) \approx 27.10\text{ MPa}.

  4. Add the initial atmospheric pressure: P2=P1+ΔP=0.10 MPa+27.10 MPa=27.2 MPaP_2 = P_1 + \Delta P = 0.10\text{ MPa} + 27.10\text{ MPa} = 27.2\text{ MPa}.

Final answer

P=27.2 MPaP = 27.2\text{ MPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how to convert all temperatures to Kelvin when applying thermodynamic state equations.

  • Practice integrating dPdT=ΔHTΔV\frac{dP}{dT} = \frac{\Delta H}{T \Delta V} across small temperature intervals using ln⁡(T2/T1)\ln(T_2/T_1).

Lock it in

Similar question

01

At 1.00 atm1.00\text{ atm}, benzene freezes at 5.50∘C5.50^\circ\text{C} (278.65 K278.65\text{ K}) with ΔHfus=9.87 kJ/mol\Delta H_{\text{fus}} = 9.87\text{ kJ/mol}. Solid benzene has a density of 1.012 g/cm31.012\text{ g/cm}^3 and liquid benzene has a density of 0.879 g/cm30.879\text{ g/cm}^3 (M=78.11 g/molM = 78.11\text{ g/mol}). Determine the sign of ΔVfus\Delta V_{\text{fus}} and calculate its value in m3/mol\text{m}^3/\text{mol}.

Answer

ΔVfus=+1.168×10−5 m3/mol\Delta V_{\text{fus}} = +1.168 \times 10^{-5}\text{ m}^3/\text{mol} (positive).

Key steps:

  1. Vm,liquid=78.110.879×10−6=8.886×10−5 m3/molV_{\text{m,liquid}} = \frac{78.11}{0.879} \times 10^{-6} = 8.886 \times 10^{-5}\text{ m}^3/\text{mol}.
  2. Vm,solid=78.111.012×10−6=7.718×10−5 m3/molV_{\text{m,solid}} = \frac{78.11}{1.012} \times 10^{-6} = 7.718 \times 10^{-5}\text{ m}^3/\text{mol}.
  3. ΔVfus=Vm,liquid−Vm,solid=8.886×10−5−7.718×10−5=+1.168×10−5 m3/mol\Delta V_{\text{fus}} = V_{\text{m,liquid}} - V_{\text{m,solid}} = 8.886 \times 10^{-5} - 7.718 \times 10^{-5} = +1.168 \times 10^{-5}\text{ m}^3/\text{mol}.
02

Using the Clapeyron equation in linear differential form ΔPΔT≈ΔHfusTΔVfus\frac{\Delta P}{\Delta T} \approx \frac{\Delta H_{\text{fus}}}{T \Delta V_{\text{fus}}}, by how many kelvins does the melting point of ice shift when the pressure is increased from 1.0 atm1.0\text{ atm} to 100.0 atm100.0\text{ atm}? (Use T=273.15 KT = 273.15\text{ K}, ΔHfus=6010 J/mol\Delta H_{\text{fus}} = 6010\text{ J/mol}, ΔVfus=−1.63×10−6 m3/mol\Delta V_{\text{fus}} = -1.63 \times 10^{-6}\text{ m}^3/\text{mol}, and 1 atm=1.013×105 Pa1\text{ atm} = 1.013 \times 10^5\text{ Pa}).

Answer

ΔT=−0.74 K\Delta T = -0.74\text{ K} (a depression of 0.74∘C0.74^\circ\text{C}).

Key steps:

  1. ΔP=(100.0−1.0)×1.013×105 Pa=1.003×107 Pa\Delta P = (100.0 - 1.0) \times 1.013 \times 10^5\text{ Pa} = 1.003 \times 10^7\text{ Pa}.
  2. dPdT=6010273.15×(−1.63×10−6)=−1.350×107 Pa/K\frac{dP}{dT} = \frac{6010}{273.15 \times (-1.63 \times 10^{-6})} = -1.350 \times 10^7\text{ Pa/K}.
  3. ΔT=ΔPdP/dT=1.003×107−1.350×107≈−0.74 K\Delta T = \frac{\Delta P}{dP/dT} = \frac{1.003 \times 10^7}{-1.350 \times 10^7} \approx -0.74\text{ K}.
03

Carbon dioxide (extCO2 ext{CO}_2) at its triple point (T=216.58extKT = 216.58 ext{ K}, P=5.18extbarP = 5.18 ext{ bar}) has ΔHfus=8.33 kJ/mol\Delta H_{\text{fus}} = 8.33\text{ kJ/mol}, Vm,solid=2.82×10−5 m3/molV_{\text{m,solid}} = 2.82 \times 10^{-5}\text{ m}^3/\text{mol}, and Vm,liquid=3.74×10−5 m3/molV_{\text{m,liquid}} = 3.74 \times 10^{-5}\text{ m}^3/\text{mol}. Calculate the pressure required to raise the melting point of dry ice to 220.00extK220.00 ext{ K}.

Answer

P≈147 barP \approx 147\text{ bar} (or 14.7 MPa14.7\text{ MPa}).

Key steps:

  1. ΔVfus=3.74×10−5−2.82×10−5=+9.20×10−6 m3/mol\Delta V_{\text{fus}} = 3.74 \times 10^{-5} - 2.82 \times 10^{-5} = +9.20 \times 10^{-6}\text{ m}^3/\text{mol}.
  2. Integrate: ΔP=ΔHfusΔVfusln⁡(T2T1)=83309.20×10−6ln⁡(220.00216.58)≈(9.054×108)×(0.01567)≈1.419×107 Pa=141.9 bar\Delta P = \frac{\Delta H_{\text{fus}}}{\Delta V_{\text{fus}}} \ln\left(\frac{T_2}{T_1}\right) = \frac{8330}{9.20 \times 10^{-6}} \ln\left(\frac{220.00}{216.58}\right) \approx (9.054 \times 10^8) \times (0.01567) \approx 1.419 \times 10^7\text{ Pa} = 141.9\text{ bar}.
  3. P2=P1+ΔP=5.18 bar+141.9 bar≈147 barP_2 = P_1 + \Delta P = 5.18\text{ bar} + 141.9\text{ bar} \approx 147\text{ bar}.
Loading workspace…