Resources
An industrial wastewater sample contains dissolved lead at a concentration of (where , density of solution ). A aliquot of this wastewater is treated by adding of a solution containing of sodium sulfide, . (a) Convert both initial concentrations to molarity (). (b) Identify the precipitate that forms according to solubility rules. (c) Determine the limiting reactant and calculate the mass of precipitate formed in milligrams. (Molar mass of , molar mass of )
Answer and steps
Final answer
(a) Initial , initial ; (b) Lead(II) sulfide, ; (c) Limiting reactant is ; mass of precipitate (or )
Steps
Part (a): Converting Initial Concentrations to Molarity
- Concentration of in the wastewater: The concentration is given as , which equals or . Using the molar mass of lead ():
- Concentration of in the sodium sulfide solution: The concentration is given directly in millimoles per liter: Since each formula unit of dissociates completely into two ions and one ion:
Part (b): Identifying the Precipitate
According to general solubility rules:
- All common salts containing sodium () are highly soluble.
- Most sulfide salts () are insoluble, with few exceptions (such as Group 1 cations and ).
- Heavy metal sulfides are extremely insoluble in aqueous solution.
When aqueous meets aqueous , they combine to form insoluble lead(II) sulfide, :
Part (c): Determining the Limiting Reactant and Mass of Precipitate
-
Calculate the amount of moles of each ion mixed:
- Volume of wastewater, :
- Volume of solution, :
- Identify the limiting reactant: The net ionic equation has a stoichiometric ratio: Comparing the available amounts: Therefore, is the limiting reactant, and is present in excess.
-
Calculate the mass of precipitate formed: The amount of produced is limited by :
Using the molar mass of ():
Converting to milligrams:
Typical errors
01 The student misinterprets Na₂S as providing 2 moles of sulfide ions per mole of formula unit, incorrectly identifying Pb²⁺ as the limiting reactant.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You multiplied the moles of by 2 to calculate the moles of . Since dissociates as , each formula unit contains only sulfide ion ().
- Step 4Correct
Because of the doubled sulfide moles from the previous step, you concluded that both ions were present in equimolar amounts rather than recognizing that was the limiting reactant, leading to an answer that is double the actual mass.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted the mass concentration of lead into molar concentration accurately.
You identified lead(II) sulfide as the precipitate using solubility rules.
You set up the correct net ionic equation and conversion from moles to mass of precipitate.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou applied the subscript 2 in to the sulfide ion instead of the sodium ion, incorrectly assuming produces .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dissociation Stoichiometry
For a salt , dissolution gives . Subscripts specify the count of that specific preceding element or polyatomic group.
Always write out the dissociation equation explicitly: to verify the mole ratio of each ion before calculating moles.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the dissociation of sodium sulfide: .
Calculate the moles of : .
Compare with . Since the ratio in is , is the limiting reactant.
Calculate the precipitate mass: .
Limiting reactant: ; Mass of precipitate:
02 The student forgets to multiply molar concentrations by the aliquot volume (500 mL) to determine the reacting moles, directly equating molarities to moles in a 1 L total volume.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You equated the molar concentration directly to the number of moles. Because only () of each solution was used, you must multiply each molarity by ().
- Step 4Correct
Your identification of as limiting was qualitatively correct because both volumes were identical, but the calculated mole quantity of precipitate formed carries over the factor-of-two error.
- Step 5Correct
Your multiplication by the molar mass was executed correctly, but due to using instead of , the resulting mass is twice the correct value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the mass concentration in parts per million to molarity using the molar mass of lead.
You converted millimoles per liter into molarity accurately.
You correctly predicted that lead(II) sulfide forms as an insoluble precipitate.
You used the correct molar mass and mole-to-mass conversion method for lead(II) sulfide.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the numerical molarity values as mole amounts without accounting for the aliquot volume.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing concentration (, in ) with absolute amount (, in ). When an aliquot is smaller or larger than , the absolute moles must be determined via before performing stoichiometric comparisons.
REASONING PATH
Your ACEpath teacher’s suggested approach- Volume Check for Moles
, where must be expressed in liters.
Whenever you are given a volume other than , multiply the molarity by the volume in liters before comparing limiting reactants.
- Distinguishing Concentration from Amount
Molarity () describes how crowded solute particles are; moles () describes the actual count of particles present.
Check your units at every line: never write next to a value that came directly from a figure without an explicit volume multiplication.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate moles of : .
Calculate moles of : .
Determine limiting reactant: since the reaction is , is limiting because .
Calculate mass of : (to 3 significant figures).
Limiting reactant is ; mass of precipitate formed (or )
03 The student chooses the reactant with the smaller molar concentration as limiting without realizing it was already in smaller moles, but then uses the excess reactant's moles to calculate the precipitate mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You identified as the limiting reactant, but you accidentally grabbed the moles of excess () instead of the limiting reactant () when calculating the mass of formed.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted mass concentration and millimolar units into molarity.
You applied solubility rules accurately to predict the formation of .
You calculated the moles of each reactant in the mixed volume and properly deduced that is limiting.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou chose (from ) rather than (from ) when computing the mass of the precipitate.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisDisconnecting the conclusion of the limiting-reactant check from the yield calculation. Once you identified the limiting reactant, you did not carry its mole amount forward into the product stoichiometry.
REASONING PATH
Your ACEpath teacher’s suggested approach- Linking the Limiting Reactant to Theoretical Yield
The maximum amount of product that can form is determined strictly by the moles of the limiting reactant, not the excess reactant.
Circle or label the limiting reactant's mole value as immediately after identifying it, and explicitly use that value to compute the product yield.
CORRECTED PATH
ACEpath Teacher's DemonstrationBecause the stoichiometric ratio is , the amount of precipitate is .
Calculate mass: .
Convert to milligrams: .
(or )
Lock it in
When of completely dissolves in water, how many moles of and ions are released?
and . Subscripts denote the quantity of the preceding element.
Similar question
A sample of is mixed with of . Identify the limiting reactant and calculate the mass of precipitate formed. (Molar mass of )
Answer
is limiting; mass of .\n1. .\n2. .\n3. Reaction: . Required for all chromate is , so limits.\n4. .\n5. .
A solution contains of . If an excess of solution is added, calculate the mass of precipitate produced. (Molar mass of )
Answer
Mass of .\n1. .\n2. Each mole of yields of , so .\n3. Precipitate reaction: .\n4. .
A wastewater aliquot of containing of (, molar mass of ) is treated with of . Determine the limiting reactant and the residual concentration (in ) of the excess ion remaining in the final mixed volume of , assuming negligible solubility of .
Answer
Limiting reactant: ; Excess ().\n1. .\n2. .\n3. .\nWait, comparing: , so is the limiting reactant!\nExcess .\nFinal .