Resources
Consider the following two standard half-cell reduction potentials at : (1) , (2) , An electrochemical engineer intends to couple these two half-reactions into a spontaneous galvanic cell. Write the balanced spontaneous overall cell reaction, determine the cathode and anode half-reactions, and calculate the standard electromotive force . Explicitly avoid the common sign convention error of multiplying the reduction potential by stoichiometric coefficients when balancing the electron count.
Answer and steps
Final answer
Cathode: ; Anode: ; Overall: ;
Steps
Identify the Cathode and Anode
For a galvanic (voltaic) cell to function spontaneously under standard conditions, the overall standard cell potential must be positive ().
The standard reduction potentials are:
- ,
- ,
The species with the more positive (higher) reduction potential has a greater tendency to gain electrons and undergo reduction. Therefore:
- Cathode (Reduction): The half-reaction takes place at the cathode:
- Anode (Oxidation): The half-reaction has the lower potential and is reversed to proceed as an oxidation at the anode:
Determine the Balanced Overall Reaction
To balance the transfer of electrons:
- The oxidation of produces .
- The reduction of consumes .
Multiply the reduction half-reaction by so that both half-reactions involve electrons:
Adding the two half-reactions eliminates the electrons and yields the balanced spontaneous overall cell equation:
Calculate the Standard Cell Potential ()
The standard electromotive force of the cell is calculated using standard reduction potentials:
Substitute the given standard reduction potentials:
Important Pitfall:
Standard reduction potential () is an intensive property, meaning its value represents potential energy per unit charge () and does not depend on the amount of material reacting. Even though the reduction half-reaction was multiplied by to balance the electrons, never multiply by a stoichiometric coefficient.
Typical errors
01 The student multiplies the standard reduction potential of the iron half-cell by the stoichiometric coefficient 3 when balancing electrons, incorrectly yielding E°cell = +3.057 V.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Cathode: Anode:
- Step 2
Overall:
- Step 3Correct
Standard reduction potential is an intensive property and does not depend on the stoichiometric coefficient used to balance electrons. It should remain .
- Step 4Correct
Your formula and arithmetic were evaluated consistently with your previous step, but the final value is incorrect because it inherited the scaled cathode potential.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the cathode and anode based on standard reduction potentials.
You reversed the oxidation half-reaction and correctly wrote the balanced overall redox equation.
You used the correct relationship .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated standard reduction potential as an extensive property like enthalpy () or Gibbs free energy (), rather than an intensive property (energy per unit charge, ) that remains constant regardless of the reaction stoichiometry.
REASONING PATH
Your ACEpath teacher’s suggested approach- Intensive vs. Extensive Properties in Electrochemistry
Standard cell potential is an intensive property with units of volts (). Multiplying a half-reaction by an integer does not change the potential difference per coulomb transferred.
Never multiply standard reduction potentials () by stoichiometric balancing factors.
CORRECTED PATH
ACEpath Teacher's DemonstrationKeep the standard reduction potential of the cathode reaction unaltered: .
Substitute the unaltered standard reduction potentials into :
Cathode: ; Anode: ; Overall: ;
02 The student reverses the cathode and anode assignments by choosing the half-reaction with the lower reduction potential as the reduction process, resulting in a negative cell potential.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Cathode: Anode:
CorrectCathode: ; Anode:
In a spontaneous galvanic cell, the half-reaction with the more positive standard reduction potential undergoes reduction at the cathode. Because , is reduced at the cathode, while is oxidized at the anode.
- Step 2
Overall:
CorrectYou balanced the electron transfer correctly by multiplying the single-electron reaction by 3, but the overall equation is reversed because of the inverted cathode and anode assignments.
- Step 3Correct
You correctly used the relationship and properly treated as an intensive property, but substituting your reversed electrodes led to a negative electromotive force rather than a positive one.
WHAT YOU DID WELL
Compliments from Your TeacherYou balanced the 3-electron and 1-electron half-reactions using the correct 1:3 stoichiometric ratio.
You correctly recalled and used the standard potential difference formula .
You avoided scaling standard potentials by stoichiometric coefficients.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou selected the species with the more negative reduction potential to undergo reduction at the cathode instead of the species with the more positive reduction potential, yielding a non-spontaneous cell.
REASONING PATH
Your ACEpath teacher’s suggested approach- Cathode Selection in Galvanic Cells
For a spontaneous galvanic cell under standard conditions, . The half-reaction with the more positive (higher) acts as the cathode (reduction).
Compare reduction potentials first: set the higher potential as and reverse the lower-potential reaction to run as oxidation at the anode.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare the standard reduction potentials: and . Since , reduction occurs at the cathode: .
Reverse the half-reaction for the anode oxidation: .
Multiply the cathode half-reaction by and add both half-reactions to obtain the overall spontaneous equation: .
Calculate standard cell potential: .
Cathode: ; Anode: ; Overall: ;
03 The student changes the sign of the oxidation potential for the anode reaction and then accidentally subtracts it instead of adding it in the cell potential formula, obtaining +0.027 V.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You reversed the sign of the anode potential to find , but then subtracted it from . If you use oxidation potential, you must add: . Alternatively, keep standard reduction potentials and subtract: .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified reduction at the cathode and oxidation at the anode using the given standard reduction potentials.
You balanced the number of electrons transferred to obtain the correct overall equation.
You recognized that standard electrode potentials are intensive and did not multiply them by stoichiometric coefficients.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou converted the anode potential into an oxidation potential but still used subtraction, effectively double-reversing the sign.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the two standard cell potential formulas: (where both potentials are standard reduction potentials) versus (where the oxidation potential has already had its sign flipped).
REASONING PATH
Your ACEpath teacher’s suggested approach- Method 1: Standard Reduction Potential Formula
Use the tabulated reduction potential directly for both terms without flipping any signs.
- Method 2: Sum of Reduction and Oxidation Potentials
If you reverse the sign of the anode potential to represent oxidation, add it to the reduction potential.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the formula using standard reduction potentials: .
Substitute the given reduction potentials: .
Evaluate the arithmetic: .
Cathode: ; Anode: ; Overall: ;
Lock it in
Why is standard electrode potential () considered an intensive property?
represents electric potential, which is energy per unit charge (). Because it measures ratio rather than total quantity, it does not change with the amount of material or stoichiometric coefficients.
Similar question
Given standard reduction potentials and , write the balanced spontaneous overall cell reaction and calculate .
Answer
Cathode: (); Anode: (). Balanced overall reaction: . Standard cell potential: .
A galvanic cell couples the half-reactions () and (). Determine the balanced overall equation and calculate .
Answer
Zinc has the higher potential (more positive/less negative), so is reduced at the cathode and is oxidized at the anode. Balanced overall reaction: . Cell potential: .
Using the thermodynamic relationship , explain why tripling the coefficients of a cell reaction triples but leaves unchanged.
Answer
Tripling the stoichiometric coefficients triples the moles of electrons transferred (). Since is an extensive state function, the total free energy change triples: . Substituting into the relation gives . The factor of 3 cancels out, proving is an intensive property.