Resources
A student measures blood glucose concentration from an isolated tissue perfusion assay. The laboratory spectrometer outputs glucose concentration in SI clinical units of . To compare this measurement with standard US physiological reference ranges, convert this concentration into milligrams per deciliter (), given that the molar mass of D-glucose is and .
Answer and steps
Final answer
Steps
Identify the conversion factors
To convert the concentration from millimoles per liter () to milligrams per deciliter (), use dimensional analysis (the factor-label method) by setting up conversion factors for both mass and volume.
- Moles to Mass:
The molar mass of glucose is , which is equivalent to: Therefore, the conversion factor is . - Liters to Deciliters:
Therefore, the conversion factor is .
Set up the dimensional analysis
Multiply the given concentration by the conversion factors so that undesirable units cancel out:
Notice how the units cancel:
- in the numerator cancels with in the denominator.
- in the denominator cancels with in the numerator.
- This leaves the target units of .
Calculate the numerical value
Combine the numerical terms:
Round to appropriate significant figures
The initial value, , contains three significant figures. Rounding to three significant figures yields:
(Pitfall note: Be careful with the metric prefix conversions. A common mistake is multiplying by instead of dividing by when converting liters in the denominator to deciliters).
Typical errors
01 The student multiplies by 10 instead of dividing by 10 when converting the volume unit in the denominator from liters to deciliters.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the liter unit is in the denominator of , the conversion factor must place liters in the numerator ( so that cancels out. Multiplying by incorrectly suggests that a deciliter contains ten times as much dissolved substance as an entire liter.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that of glucose equals .
You accurately calculated the intermediate concentration in milligrams per liter (.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up the volume conversion factor with deciliters in the numerator rather than arranging units to cancel liters in the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating denominator unit conversions like numerator unit conversions instead of tracking explicit cancellation via dimensional analysis, along with not checking whether the smaller volume () should contain less total solute than .
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Cancellation Alignment
To cancel a unit located in the denominator, that same unit must appear in the numerator of the conversion factor: .
Write out conversion factors as complete fractions with explicit units before multiplying, and cross out matching numerator and denominator pairs.
- Physical Reality Check
A deciliter is one-tenth of a liter (), so a sample must contain one-tenth of the solute mass present in a sample.
Ask yourself if the resulting concentration per deciliter should be larger or smaller than the concentration per liter.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the conversion factor using with liters in the numerator to cancel the denominator: .
Multiply the mass concentration by the conversion factor: .
Round to three significant figures to match the given value of .
02 The student divides by the molar mass instead of multiplying when converting moles to grams.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You divided by the molar mass () rather than multiplying. Because , you must multiply by so that the millimole units cancel out.
- Step 2Correct
Your volume conversion logic of dividing by to go from per liter to per deciliter was correct, but this final result was affected by dividing by molar mass in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the factor of needed to convert liters in the denominator to deciliters.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by molar mass instead of multiplying when converting chemical amount (moles) to mass (grams).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInversion of dimensional analysis units: writing the molar mass ratio as instead of , leading to division rather than multiplication.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Cancellation Check
Set up units as algebraic fractions so that the original unit is in the opposite position (numerator vs. denominator) of the conversion factor: .
Write out the full unit labels inside conversion factors rather than bare numbers, and cross out matching pairs before computing.
- Magnitude Reality Check
One mole of a substance has a mass of many grams; therefore, a given number of millimoles must yield a much larger numerical mass in milligrams.
Before finishing, verify that converting from millimoles to milligrams makes the numerical value increase, not decrease.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply the concentration by the molar mass: .
Convert liters to deciliters using : .
Round to three significant figures to match the given .
03 The student misinterprets deciliters as 100 per liter instead of 10, confusing deciliters with centiliters.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You divided by instead of . Because , each deciliter contains one-tenth of the mass present in a full liter, requiring division by .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that multiplying millimoles by the molar mass (, or ) converts the substance amount into milligrams.
You recognized that moving from a liter to a smaller unit in the denominator requires dividing the concentration.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeDividing by 100 instead of 10 to convert liters to deciliters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the metric prefix 'deci-' (, or ) with 'centi-' (, or ), leading to an answer that is ten times too small.
REASONING PATH
Your ACEpath teacher’s suggested approach- Metric Prefix Definition
The prefix 'deci-' means one-tenth ( or ), meaning . In contrast, 'centi-' means one-hundredth ( or ).
Always double-check the metric factor provided in the problem prompt before calculating.
- Denominator Unit Cancellation
When converting a unit in the denominator, set up a conversion factor where the old unit is in the numerator: .
Write out the units explicitly in factor-label format so that unwanted units cancel cleanly.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the conversion using the given relation : .
Round the final value to three significant figures to match the measured input .
Lock it in
When converting a unit in the denominator (such as in ), where must that unit be placed in your conversion factor?
In the numerator, so that cancels out the original unit.
Similar question
A patient's blood serum cholesterol level is measured as . Convert this concentration to , given that the molar mass of cholesterol is and . Express your answer to three significant figures.
Answer
. Multiply by molar mass: . Then divide by : .
A clinical laboratory reports an extracellular calcium concentration of . Convert this value into milligrams per deciliter (), given that the atomic mass of calcium is and . Round to three significant figures.
Answer
. Convert to : . Convert to : .
A researcher needs to prepare a saline buffer with a sodium chloride concentration of . What is this concentration expressed in ()? Write your answer with appropriate units and key dimensional analysis steps.
Answer
. Set up dimensional analysis to cancel liters in the denominator: .