Resources
An agricultural physiology experiment measures the photosynthetic carbon fixation rate of a greenhouse tomato crop canopy. The canopy assimilates carbon dioxide at a rate of of leaf area. (a) Express this carbon assimilation rate in units of (molar mass of ). (b) Assuming standard stoichiometry where fixing requires and , calculate the consumption rate of and in .
Answer and steps
Final answer
(a) ; (b) and .
Steps
Part (a): Converting the Carbon Fixation Rate
-
Understand the given units and target units:
- Given assimilation rate:
- Molar mass of :
- Target rate: micromoles of per square meter per second ()
-
Convert mass of per minute to moles per minute:
- First, convert milligrams () to grams ():
- Divide by the molar mass to find the number of moles assimilated per minute:
-
Convert moles to micromoles ():
- Since :
-
Convert the time unit from minutes to seconds:
- There are in . Dividing by yields:
- Rounded to three significant figures, the carbon assimilation rate is .
Pitfall to avoid: Do not forget to convert both the mass unit () and the time unit (). A common error is multiplying by instead of dividing when converting per-minute rates to per-second rates.
Part (b): Calculating the Consumption Rates of and
-
Review the stoichiometric requirements of the pathway (Calvin Cycle):
- Fixing requires and (used during the reduction of 3-phosphoglycerate and the regeneration of RuBP).
-
Calculate the rate of consumption:
- Multiply the fixation rate by the stoichiometric coefficient of ():
-
Calculate the rate of consumption:
- Multiply the fixation rate by the stoichiometric coefficient of ():
Typical errors
01 The student multiplies by 60 instead of dividing by 60 when converting per minute to per second.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because time is in the denominator (rate per minute), converting to rate per second requires dividing by , not multiplying by . Multiplying caused the per-second rate to be times too large.
- Step 3Correct
Your stoichiometric reasoning of multiplying the assimilation rate by for and by for is completely correct, but the final numerical values were affected by the time-unit conversion error from step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the molar mass of () to find the molar quantity in micromoles.
You identified and applied the proper stoichiometric multipliers for () and () in the Calvin cycle.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the minute unit as a factor in the numerator rather than the denominator, multiplying by instead of dividing by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing unit cancellation when converting rates where the target unit appears in the denominator ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Denominator Unit Conversion
When a unit is in the denominator, multiply by the conversion factor that places that unit in the numerator: .
Always write out conversion factors with explicit fraction bars and cancel units crosswise before calculating.
- Sanity Check on Time Rates
A process running for only one second must produce or consume less substance than it does over a full minute.
Check whether the numeric value decreases when moving from per-minute to per-second rates.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert per minute to per second: .
Calculate consumption rate: .
Calculate consumption rate: .
(a) ; (b) and
02 The student inverts the stoichiometric ratios of ATP and NADPH relative to CO2 fixation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because each mole of requires , the rate of consumption must be three times larger than the assimilation rate, requiring multiplication rather than division.
- Step 4Correct
Because each mole of requires , you need to multiply the carbon assimilation rate by rather than dividing by .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted milligrams to micromoles using the molar mass of .
You correctly divided by seconds to convert minutes to seconds.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up the stoichiometric conversion factor upside-down, dividing by the stoichiometric requirement instead of multiplying.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing whether a stoichiometric ratio acts as a multiplier or a divisor when scaling up a reagent consumption rate from a known substrate rate.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Analysis Check
Always write full units in stoichiometric ratios: .
Ensure that the units of the given rate () cancel out in the denominator.
- Sanity Check on Reagent Proportions
If a reaction consumes multiple moles of cofactor per mole of substrate, the cofactor consumption rate must exceed the substrate consumption rate.
Verify that your resulting and rates are greater than the fixation rate.
CORRECTED PATH
ACEpath Teacher's DemonstrationMultiply by the stoichiometric ratio for : .
Multiply by the stoichiometric ratio for : .
(a) ; (b) and .
03 The student forgets to convert the time unit from minutes to seconds, leaving the rate on a per-minute basis.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You correctly converted moles to micromoles (), but you labeled the rate as per second without dividing by . The value is the assimilation per minute.
- Step 3Correct
Your stoichiometric reasoning is completely sound because requires . The numerical value is affected only by the uncorrected per-minute rate from step 2.
- Step 4Correct
Your stoichiometric multiplication by for is correct, but the result inherits the missing time conversion from step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted milligrams to grams and divided by the molar mass of () to find the molar quantity.
You accurately converted moles to micromoles by multiplying by .
You applied the standard Calvin cycle stoichiometric ratios of and flawlessly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou replaced with in your unit label without dividing the numerical value by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisDimensional analysis step skipped: when converting a rate from per-minute () to per-second (), time is in the denominator, so you must divide by rather than simply renaming the unit.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Cancellation Check
, so .
Write out conversion factors explicitly with cancelling units: .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the per-minute carbon assimilation rate to a per-second rate: .
Calculate the consumption rate using the ratio: .
Calculate the consumption rate using the ratio: .
(a) ; (b) and .
Lock it in
How do you convert a rate expressed in to ?
Divide by (multiply by ). Because a second is shorter than a minute, less quantity is processed per second.
Similar question
A cell culture produces of lactic acid (molar mass ) per minute. Calculate the production rate in .
Answer
. First, . Then divide by : .
A photosynthetic leaf disc assimilates . Assuming standard stoichiometry ( and per fixed), how many millimoles () of and are consumed by of leaf area over a period?
Answer
and . In (), total fixed . Multiplying by stoichiometric coefficients: ; .
During photorespiration in a plant, the oxygenation of RuBP by RuBisCO consumes at (molar mass of ). If each oxygenation event requires an extra investment of equivalents during the photorespiratory carbon oxidation cycle, determine the rate of consumed by photorespiration in .
Answer
. Convert rate: . Divide by : . Multiply by : .