Resources
A limnologist studies a population of green microalgae (Chlorella vulgaris) growing in a bioreactor. The carrying capacity is reported in chemical biomass terms as . Through laboratory cell-mass calibration, the average dry weight of a single Chlorella cell is determined to be . Convert this carrying capacity and determine: (a) the carrying capacity in units of , and (b) the total carrying capacity of the entire bioreactor vessel in total number of cells.
Answer and steps
Final answer
(a) ; (b)
Steps
Carrying capacity () represents the maximum population size or biomass that an environment can sustainably support. When expressed in biomass concentration, it can be converted to cell density and total population size using the average mass per cell and the total volume of the culture vessel.
Part (a): Find the Carrying Capacity in
- Convert biomass density to grams per liter (): The given biomass concentration is . Since :
- Calculate cell density in : Divide the total biomass density by the average dry mass of a single cell ():
- Convert to : Since :
Common Pitfall: Forgetting to convert milligrams to grams before dividing by the cell mass in grams will result in an answer off by a factor of . Always verify that mass units cancel properly.
Part (b): Find the Total Carrying Capacity of the Bioreactor
To determine the total number of cells () the bioreactor can support, multiply the density in by the total volume of the bioreactor ():
Typical errors
01 The student forgets to convert milligrams to grams, directly dividing milligrams per liter by grams per cell and overestimating the cell concentration and total population by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You divided biomass in milligrams () by cell mass in grams () without converting them to the same mass unit first. Because , is equal to , which gives .
- Step 2Correct
Your conversion factor from liters to milliliters (dividing by ) was entirely correct, but the result was shifted by the error from Step 1.
- Step 3Correct
You correctly multiplied the volumetric cell density by the total culture volume to determine total population carrying capacity, but the value carried forward the factor-of- error from Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that dividing biomass density by individual cell mass yields cell population density.
You applied the correct conversion factor between liters and milliliters.
You correctly multiplied volumetric density by total bioreactor volume to find the total carrying capacity.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided milligrams by grams directly without converting milligrams into grams ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking unit cancellation when working with multi-tier metric prefixes ( vs. ). When quantities with different metric prefixes are combined in a quotient, their units must be reconciled before carrying out numerical division.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Cancellation Check
Units cannot cancel across different metric prefixes: , not .
Write out explicit conversion factors (such as ) directly into your dimensional analysis setup before calculating.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b)
02 The student multiplies by 1000 instead of dividing by 1000 when converting cells per liter to cells per milliliter, resulting in a concentration that is 10⁶ times too large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because is in the denominator, converting from per liter to per milliliter requires dividing by , not multiplying. One milliliter is a much smaller volume than one liter, so it must contain fewer cells.
- Step 3Correct
This final value for part (a) is off by a factor of because of the multiplication error in the volume conversion.
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted biomass concentration from milligrams per liter to grams per liter.
You accurately divided the biomass density by the single-cell dry weight to find cells per liter.
You correctly set up and solved for the total carrying capacity in part (b) by multiplying density per liter by total volume in liters.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou knew that , but you multiplied by instead of dividing by because the volume unit is in the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating compound units (like ) as numerator quantities when converting units. When a unit is in the denominator, replacing a larger volume (liters) with a smaller volume (milliliters) requires dividing by the conversion factor.
REASONING PATH
Your ACEpath teacher’s suggested approach- Denominator Unit Factor Setup
To convert to , multiply by .
Always write out conversion factors with explicit fraction bars so that identical units cancel diagonally.
- Physical Reality Check
A smaller sample volume must hold fewer individuals at the same concentration.
Check that your numerical density in is times smaller than your density in .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the dimensional conversion factor: .
Divide: .
Round to three significant figures to match the given data: .
(a) ; (b)
03 The student uses the calculated cells/mL concentration directly with the bioreactor volume in liters without converting units, underestimating the total vessel cell count by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You multiplied a density in by a total volume in . Because , the volume units and do not cancel directly. You either need to use your concentration in or convert the vessel volume to milliliters ().
WHAT YOU DID WELL
Compliments from Your TeacherYou converted milligrams per liter to grams per liter with the correct factor of .
You used the single-cell dry weight to determine the cell density per liter.
You correctly calculated the carrying capacity in for part (a).
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally grabbed the value instead of your earlier value when multiplying by the bioreactor volume given in liters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIncomplete dimensional analysis tracking during multi-step unit conversions, where volume denominator units () failed to match vessel volume units ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Consistency Check
Total Quantity = Concentration Volume only when the volume units in the concentration denominator and the total volume match exactly: or .
Always write out and cancel the explicit units before calculating the numerical product.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the density in to match the bioreactor volume unit of liters: .
Alternatively, convert the bioreactor volume to : , then multiply: .
Evaluate the product: , and .
(a) ; (b)
Lock it in
When dividing total biomass in by individual cell weight in , what must you do first?
Convert both masses to the same unit (multiply by or by ) so that the mass units cancel.
Similar question
A yeast culture reaches a carrying capacity of . If a single yeast cell has an average mass of , find the carrying capacity in .
Answer
. Key steps: Convert biomass density to : . Compute density: . Convert to : .
A marine diatom population in a coastal mesocosm has a carrying capacity of . The average dry weight of one diatom cell is . Calculate: (a) the carrying capacity in , and (b) the total diatom population at carrying capacity in the mesocosm.
Answer
(a) ; (b) . Key steps: (a) Convert . Cell density . (b) Total cells .
A photobioreactor holds of cyanobacteria. The target carrying capacity is . Each cell has an average mass of . Determine the total dry biomass (in kilograms, ) present in the reactor when the population reaches carrying capacity.
Answer
(or ). Key steps: Cell density in . Total cells . Total biomass .